DSA8300 Datasheet

Digital Serial Analyzer Sampling Oscilloscope

Tektronix 不再銷售此產品規格表上的產品。
檢視 Tektronix Encore 以取得檢修測試設備。
檢查這些產品的支援和保固狀態。

Replacement Products

8 系列取樣示波器

Digital Serial Analyzer Sampling Oscilloscope

The DSA8300 is a state-of-the-art Equivalent Time Sampling Oscilloscope that provides the highest fidelity measurement and analysis capabilities for Communications Signal Analysis, Serial Data Network Analysis, and Serial Data Link Analysis applications.

Notice to EU customers

This product is not updated to comply with the RoHS 2 Directive 2011/65/EU and will not be shipped to the EU. Customers may be able to purchase products from inventory that were placed on the EU market prior to July 22, 2017 until supplies are depleted. Tektronix is committed to helping you with your solution needs. Please contact your local sales representative for further assistance or to determine if alternative product(s) are available. Tektronix will continue service to the end of worldwide support life.

Key performance specifications

Low time base jitter:
- 425 fs typical on up to 8 simultaneously acquired channels
- <100 fs on up to 6 channels with 82A04B phase reference module
Industry’s highest vertical resolution – 16 bit A/D
Electrical resolution: <20 µV LSB (for 1 v full range)
Optical resolution from <20 nW for the 80C07B (1 mW full range) to <0.6 µW for the 80C10C (30 mW full range)
Optical bandwidths to >80 GHz
Electrical bandwidths to >70 GHz
Over 120 automated measurements for NRZ, RZ, and pulse signal types
Automated mask testing with over 80 industry-standard masks
Complex jitter/noise/BER/SER analysis (80SJNB), support for complex measurements TDECQ ¹, SNDR ² (applications)

¹Transmitter and Dispersion Eye Closure Quaternary for PAM4.

²Signal-to-Noise-and-Distortion Ratio.

Key features

A wide variety of optical, electrical, and accessory modules support your specific testing requirements.

¹Optical Reference Receiver (ORR) is a 4th-order Bessel-Thompson filter, with a frequency response and tolerances as defined by the standards. Tektronix optimizes the response for best nominal fit and highest quality mask test results.

²Refer to the 80E00 Electrical Sampling Modules datasheet for detailed descriptions of each available module.

Applications

Design/Verification of telecom and datacom components and systems
Manufacturing/testing for ITU/ANSI/IEEE/SONET/SDH compliance
High-performance true-differential TDR measurements
Impedance characterization and network analysis for serial data applications including S-parameters
Advanced jitter, noise, BER and SDLA analysis
Channel and eye diagram simulation and measurement-based modeling with IConnect.

Superior performance with extraordinary versatility

The DSA8300 Digital Serial Analyzer is the most versatile tool for developing and testing communications, computers, and consumer electronics which use multi-gigabit data transmission. It is used for optical and electrical transmitter characterization, as well as compliance verification for devices, modules, and systems used in these products.

In addition, the DSA8300 is well-suited for electrical signal path characterization, whether for packages, PCBs, or electrical cables. With exceptional bandwidth, signal fidelity, and the most extensible modular architecture, the DSA8300 provides the highest-performance TDR and interconnect analysis, most accurate analysis of signal impairments, and BER calculations for current and emerging serial data technology.

DSA8300-Digital-Serial-Analyzer-Sampling-Oscilloscope-Datasheet-EN_US-9-L

Optical eye diagram testing

DSA8300-Digital-Serial-Analyzer-Sampling-Oscilloscope-Datasheet-EN_US-10-L

Passive interconnect test

Finally, with its exceptional signal fidelity and resolution, the DSA8300 is the gold standard for electrical and optical applications which require ultra-high bandwidths, very fine vertical resolution, low jitter, and/or exceptionally low noise.

The DSA8300 provides unmatched measurement system fidelity with the lowest native instrument jitter floor (425 fs RMS, typical for serial data signals at rates >1.25 Gb/s) that ensures the most accurate acquisition of up to 8 high-bandwidth signals simultaneously. You get additional analysis benefits from acquisition jitter below 100 fs RMS when using the 82A04B Phase Reference module.

The multiprocessor architecture, with dedicated per-slot digital signal processors (DSPs), provides fast waveform acquisition rates, reducing the test times necessary for reliable characterization and compliance verification.

The DSA8300’s versatile modular architecture supports a large and growing family of plug-ins enabling you to configure your measurement system with a wide variety of electrical, optical, and accessory modules that best suit your application now and in the future. With 6 module slots, the DSA8300 can simultaneously accommodate a Clock Recovery module, a precision Phase Reference module, and multiple acquisition modules (electrical or optical), so you can match system performance to your evolving needs. The ability to swap sampling modules without powering down the DSA8300 (available for scopes with firmware versions 6.1 and later) provides additional flexibility in configuring your DSA8300 to changing test needs.

In addition, specialized modules supporting features such as single-ended and differential electrical clock recovery, electrostatic protection for electrical samplers, and connectivity to the popular TekConnect^®probing system brings you the performance of state-of-the-art Tektronix probes for high-impedance and differential probing. Low-impedance probes for 50 Ω probing and for TDR probing are also available.

The raw acquisition performance of the DSA8300 and its sampling modules and accessories is further augmented by the comprehensive measurement and analysis capabilities of the DSA8300 and its associated software applications.

See the Ordering information for a list of currently available software applications and modules.

Measurement and analysis tools for optical testing applications

The DSA8300 includes a wide variety of measurement and analysis tools which specifically address optical testing applications. In addition to the standard amplitude and timing parametric measurements (such as rise/fall times, amplitude, RMS jitter, RMS noise, frequency, period, and so on), the measurement suite for the DSA8300 includes measurements specifically tailored to measuring optical signals (average optical power, extinction ratio, eye height, eye width, optical modulation amplitude (OMA), and so on). For a complete list of measurements, see theMeasurementsection of this datasheet.

The DSA8300 also includes standard compliance testing masks for all of the common optical standards from 155 Mb/s to 100 Gb/s. The DSA8300 mask testing system includes the ability to automatically fit standard and user masks to data acquired into a waveform database. The mask test system can also automatically determine the mask margin based either on the total number of mask violations or the "hit ratio" of mask violation to the number of samples acquired in the mask test unit interval. Users can also create custom masks for automated mask testing. Histograms and cursor measurements are also available to analyze optical signals acquired by the DSA8300.

Test solutions

The DSA8300, with its highly configurable mainframe and a wide variety of modules, provide complete test solutions with superior system fidelity.

Optical modules
The Tektronix 80C00 family of optical sampling modules cover a range of wavelengths for both single- and multi-mode fibers. The various modules provide a range of features such as clock recovery, reference receiver filters, and a wide range of standards test solutions.
Refer to the Ordering information section for a list of currently available optical modules.
Refer to the 80C00 Optical Modules datasheet for detailed descriptions of each available module.

Electrical modules
The Tektronix 80E00 family of electrical sampling modules provide a wide variety of capabilities, allowing the user to configure a test solution specifically adapted to their application. A wide variety of bandwidth solutions is available along with other features such as Time Domain Reflectometry or S-parameter testing.
Refer to the Ordering information section for a list of currently available electrical modules.
Refer to the 80E00 Electrical Sampling Modules datasheet for detailed descriptions of each available module.

Utility modules
The Tektronix 80A00 and 82A00 families of modules provide additional capabilities such as phase reference and ESD protection.
Refer to the Ordering information section for a list of currently available utility type modules.
Refer the to the various utility module datasheets for detailed descriptions of each available module.
- 80A02 EOS ESD Isolation Module
- 82A04B Phase Reference Module
- 80A03 module extender

80B28G - a DSA8300 product bundle for 28 Gb/s applications

This bundle, when used with a DSA8300, provides all of the electrical sampling modules, accessories, and clock recovery capabilities needed to test applications at rates from 10 Gb/s to 28.6 Gb/s per lane. The bundle includes the following products:

1 ea. 80E09B: dual channel, 70 GHz Remote Electrical Sampling Module
1 ea. 82A04B: Phase Reference Module that supports sub-100 fs instrumentation jitter when used with the 80E09B
1 ea. CR286A with Option HS: 28.6 GHz clock recovery instrument that supports clock recovery at rates from 150 Mb/s to 28.6 Gb/s
1 ea. 80X01: 1-meter sampling module extender cable used to extend the phase reference module to connect directly to the clock recovery module
1 ea. 80A08 : accessory kit with all of the necessary cables, adapters, DC blocks and other accessories to configure a complete test solution

To extend this solution to test additional lanes in a multi-lane application, simply install additional 80E09B dual channel remote sampling modules.

Specifications

Product specifications and descriptions in this document are subject to change without notice.

All specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.

Vertical system

Rise Time / Bandwidth: Determined by the sampling modules used

Vertical Resolution

16 bits over the sampling modules' dynamic range

Electrical Resolution: <20 μV LSB (for 1 V full range)

Optical resolution depends on the dynamic range of the optical module – ranges from <20 nW for the 80C07B (1 mW full range) to <0.6 μW for the 80C10C (30 mW full range)

Horizontal system

Main and Magnification View Time Bases, Horizontal Scale: 100 fs/div to 1 ms/div, in 1-2-5 sequence or 100 fs increments

Time Interval Accuracy

Trigger Direct (Front Panel) Input

Horizontal scale >20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 0.1% of interval, STDEV: ≤1 ps

Horizontal scale ≤20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 1 ps + 0.5% of interval

Clock Input/Prescale Trigger (Front Panel), Eye or Pattern Mode

Mean accuracy determined by clock input accuracy STDEV: <0.7 ps (max); <0.1 ps (typical)

Clock Input/Prescale Trigger (Front Panel), Other Mode

Horizontal scale >20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 0.1% of interval, STDEV: ≤3 ps

Horizontal scale ≤20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 1 ps + 0.5% of interval

TDR Clock Trigger (Lock to External 10 MHz Clock)

Horizontal scale >20 ps/div, right-most point of measurement interval <150 ns; Mean Accuracy: 0.01% of interval, STDEV: ≤1 ps (0.1 ps typical)

Random Phase Corrected Mode (Clock Input to 82A04B)

Maximum timing deviation 0.1% of phase reference signal period, typical, relative to phase reference signal

For more information on phase reference modes of operation, see the “Phase Reference Module for the DSA8300 Sampling Oscilloscope” datasheet.

Triggered Phase Corrected Mode (Clock Input to 82A04B)

Maximum timing deviation relative to phase reference signal:

>40 ns after trigger event: 0.2% of phase reference signal period, typical

≤40 ns after trigger event: 0.4% of phase reference signal period, typical

Horizontal Deskew Range Available

SW: –500 ps to +100 ns on any individual channel in 100 fs increments, some limitations apply to software deskew TDR and sampling modules. Note that SW deskew implies acquiring another waveform, at a different horizontal position; a throughput penalty exists.

Mainframe channel delay (HW deskew):

Sample mode:

80E11 and 80E11x1: ±35 ps

80E07B, 80E08B, 80E09B, and 80E10B: ±150 ps

80C17, 80C18: +/- 65 ps

TDR mode:

80E08B and 80E10B: ±200 ps

DSA8300 Record Length: 50, 100, 250, 500, 1000, 2000, 4000, 8000, or 16000 samples (magnification views have maximum record length of 4000 samples)

Longer Records Available

IConnect^®: 1M samples

80SJNB Jitter, Noise, and BER Analysis Software: 10M samples (100k unit intervals, 100 samples per unit interval)

Trigger system

Trigger Sources

Clock Input/Prescale Trigger (front panel)

TDR clock (generated internally)

Clock recovery triggers from Optical Sampling modules and Electrical Clock Recovery modules (internally connected)

Phase Reference (when using the 82A04B Phase Reference module) time base supports acquisitions without a trigger signal in its Free Run mode

Trigger Direct Input (front panel)

Clock Input / Prescale Trigger Input

Clock Input Sensitivity

150 mV_p-pto 1 V_p-p, 0.15 GHz to 20 GHz (typical)

200 mV_p-pto 1 V_p-p, 0.8 GHz to 15 GHz (guaranteed)

Minimum Slew Rate

≥2 V/ns

Clock Input Range

1.0 V_p-p (max) – AC coupled

Pattern Lengths Supported (for Pattern Triggering with ADVTRIG Option)

2 to 2²³ (8,388,608) inclusive

Clock Input Jitter in Clock-eye and Clock-pattern Trigger Modes (Typical)

0.15 - 0.40 GHz: 900 fs (RMS)

0.40 - 1.25 GHz: 800 fs

1.25 - 20 GHz: 425 fs

Clock Input Jitter in Clock-eye and Clock-pattern Trigger Modes (Max)

0.80 - 1.25 GHz: 900 fs (RMS)

1.25 - 11.20 GHz: 500 fs

11.20 - 15.0 GHz: 600 fs

TDR Trigger

TDR Step Rate

Selectable from 25 to 300 kHz in 1 kHz steps

Actual TDR step rate may vary up to 2% from requested rate

TDR Trigger Jitter

1.3 ps RMS (typical) 1.8 ps RMS (max)

Phase Reference Time Base

Phase Reference Input Range

Standard 82A04B: 8 - 32 GHz (guaranteed), 2 - 32 GHz (typical)

82A04B Option 60G: 8 - 60 GHz (guaranteed), 2 - 70 GHz (typical)

For non-sinusoidal clock at frequencies <8 GHz, it may be necessary to filter the clock input to eliminate harmonics from the clock signal (see accessories 020-2566-xx, 020-2567-xx, and 020-2568-xx)

Phase Reference Input Sensitivity

Best jitter performance is with the clock input to the 82A04B in the following range: 0.6 - 1.8 V. The phase reference time base remains operational to 100 mV (typical) with increased jitter

Jitter

f ≥8 GHz: 100 fs RMS, on a 10 GHz or faster sampling module

2 GHz ≤ f ≤ 8 GHz: 140 fs RMS, typical on a 10 GHz or faster acquisition module

Trigger Direct Input

Trigger Sensitivity

50 mV, DC - 4 GHz (typical)

100 mV, DC - 3 GHz (guaranteed)

Trigger Level Range

±1.0 V

Trigger Input Range

±1.5 V

Trigger Holdoff

Adjustable 5 μs to 50 ms in 0.5 ns increments

Trigger Direct Input Jitter

1.1 ps RMS + 5 ppm of horizontal position (typical)

1.5 ps RMS + 10 ppm of horizontal position (max)

Acquisition system

Acquisition modes: Sample (Normal), Envelope, and Average

Number of sampling modules accommodated

Up to 4 dual-channel electrical; up to 2 optical sampling modules.

Population of the CH1/CH2 large slot with any module other than one requiring power only displaces functionality of the CH1/CH2 small slot; population of the CH3/CH4 large slot with any module other than one requiring power only displaces functionality of the CH3/CH4 small slot.

Number of simultaneously acquired inputs: 8 channels maximum

Maximum acquisition rate

300 kS/s per channel in TDR mode

200 kS/s per channel in all other nonphase reference modes

120 kS/s per channel in phase reference modes

Waveform measurements

System Measurement Rate: The DSA8300 supports up to 8 simultaneous measurements, updated 3 times per second with optional display of per-measurement statistics (min, max, mean, and standard deviation)

Measurement Set

Over 120 automated measurements include RZ, NRZ, and pulse signal types, and the following measurement types:

Amplitude Measurements: High, Low, Amplitude, Peak-to-Peak, Max, Mid, Min, Mean, +Overshoot, –Overshoot, P-P, Average Optical Power (dBm, watts), Noise, RMS Noise, SNR, Eye Height, Eye Opening Factor, Extinction Ratio (Ratio, %, dB), Suppression Ratio (Ratio, %, dB), OMA, Q-factor, RMS, AC RMS, Cycle RMS, Cycle Mean, Gain, Crossing %, Crossing Level OMA, VMA
Timing Measurements: Rise, Fall, Period, Bit Rate, Bit Time, Frequency, Crossing Time, +Cross, –Cross, Jitter (P-P, RMS), Eye Width, +Width, –Width, Burst Width, +Duty Cycle, –Duty Cycle, Duty Cycle Distortion, Delay, Phase, Pulse Symmetry
Area Measurements: Area, Cycle Area

Cursors: Dot, vertical bar, and horizontal bar cursors

Waveform Processing: Up to 8 math waveforms can be defined and displayed using the following math functions: Add, Subtract, Multiply, Divide, Average, Differentiate, Exponential, Integrate, Natural Log, Log, Magnitude, Min, Max, Square Root, and Filter. In addition, measurement values can be utilized as scalars in math waveform definitions

Mask Testing: For many applications, standard masks are available as predefined, built-in masks. Many of the most commonly used standard masks are shown in the following supported standards list. Contact your local Tektronix representative to get a list of all available masks. Unless otherwise noted, file-based masks are used to distribute new, Tektronix factory-created, updated masks as a file loadable by the firmware. User-defined masks allow the user to create (through UI or PI) user masks

Supported standards

Type	Standard
Ethernet	100BASE-LX10 125.0 Mb/s 100BASE-BX10 125.0 Mb/s Gigabit Ethernet 1.250 Gb/s 1000BASE-KX 1.250 Gb/s 2 GBE 2.500 Gb/s 10GBASE-X4 3.125 Gb/s 10GBASE-W 9.95328 Gb/s 10GBASE-R 10.3125 Gb/s FEC11.10 11.095728 Gb/s 10GBASE-LRM 10.31250 Gb/s 40GBASE-FR 41.25 Gb/s 40GBASE-LR4 10.3125 Gb/s 40GBASE-SR4 10.3125 Gb/s 100GBASE-ER4 25.71825 Gb/s 100GBASE-LR4 25.71825 Gb/s 100GBASE-SR10 10.3125 Gb/s 100GBASE-SR4 25.7185 Gb/s
SONET/SDH	OC-1/STM-0 51.84 Mb/s OC-3/STM-1 155.52 Mb/s OC-12/STM-4 622.08 Mb/s OC-48/STM-16 2.48832 Gb/s FEC2.666 2.6660571 Gb/s OC-192/STM-64 9.95328 Gb/s FEC10.66 10.6642 Gb/s FEC10.71 10.709225 Gb/s OTU4 27.95 Gb/s OC-768/STM-256 39.81312 Gb/s FEC42.66 42.6569 Gb/s FEC43.02 43.018414 Gb/s
Fibre Channel Optical	FC133 132.81 Mb/s FC266 265.6 Mb/s FC531 531.2 Mb/s FC1063 1.0625 Gb/s FC2125 2.125 Gb/s FC4250 4.250 Gb/s 8GFC 8.500 Gb/s 10GFC 10.518750 Gb/s FC11317 11.3170 Gb/s 16GFC MM r6.1 14.025 Gb/s 16GFC SM r6.1 14.025 Gb/s 32GFC 28.05 Gb/s
Fibre Channel Electrical	FC133 132.81 Mb/s FC266 265.6 Mb/s FC531 531.2 Mb/s FC1063 1.0625 Gb/s FC2125E 2.125 Gb/s: Abs, Beta, Tx/Rx; Abs, Gamma, Tx/Rx FC4250E 4.250 Gb/s: Abs, Beta, Tx/Rx; Abs, Gamma, Tx/Rx FC8500E 8.500 Gb/s: Abs, Beta, Tx/Rx; Abs, Gamma, Tx/Rx
SATA	G1 1.500 Gb/s Tx, Rx G2 3.000 Gb/s Tx, Rx G3 6.000 Gb/s Tx, Rx

Display system

Touch Screen Display: 264 mm / 10.4 in. diagonal, color, LCD

Colors: 16,777,216 (24 bits)

Video Resolution: 1024 horizontal by 768 vertical displayed pixels

Magnification Views: In addition to the main time base, the DSA8300 supports two magnification views. These magnifications are independently acquired using separate time-base settings which allow same or faster time/div than that of the main time base

Input output ports

Front Panel

USB 2.0 Port(s): One USB 2.0 connector (instruments shipped after 12/2012 have 3 USB ports on the front panel)
Anti-static Connection: Banana-jack connector, 1 MΩ
Trigger Direct Input: See Trigger System specification
Clock Input / Prescale Trigger: See Trigger System specification
TDR Clock Output: See Trigger System specification
DC Calibration Output: ±1.25 V maximum

Rear Panel

USB Ports

4 USB 2.0 connectors

LAN Port

RJ-45 connector, supports 10/100/1000BASE-T

Serial Ports

DB-9 COM1, COM2 ports

GPIB

IEEE488.2 connector

DVI-I Video Port

DVI connector, female

Connect to show the oscilloscope display, including live waveforms on an external monitor or projector. The primary Windows desktop can also be displayed on an external monitor using these ports.

Alternatively, the DVI-I port can be configured to show the secondary Windows desktop (also called extended desktop or dual-monitor display).

DVI to VGA 15-pin D-sub connector adapter provided

PS2 Serial Ports

Mouse and keyboard inputs

Audio Ports

1/8 in. microphone input and line output

Data storage

Waveform Databases: 4 independently accumulated waveform records of up to 4M waveform points each. Variable waveform database mode with true first-in/first-out of up to 2000 waveforms available on each of 4 waveform databases (2M samples maximum / waveform database)

Hard Disk Drive: Rear-panel, removable hard disk drive, 500 GB capacity

Optical Drive: Front-panel DVD Read Only / CD Read-Write drive with CD-creation software application

Nonvolitile storage: USB 2.0 flash memory

Computer system

Operating System: Microsoft Windows 7 Ultimate (32-bit)

CPU: 3 GHz Intel Core™ 2 Duo CPU

Power source

Line voltage and frequency

90 V to 250 V

50 Hz to 400 Hz

Power Consumption

205 W, typical, mainframe only

330 W, typical, fully loaded

600 W, maximum

Physical characteristics

Dimensions

	mm	Inches
Width	475	18.0
Height	343	13.5
Depth	419	16.5

	kg	lb
Weight	21	46

EMC, environment and safety

Temperature

Operating: +10 to +40 °C
Nonoperating: –22 to +60 °C

Altitude

Operating: 3,048 m (10,000 ft.)
Nonoperating: 12,190 m (40,000 ft.)

Relative Humidity

Operating (CD-ROM not installed): 20% to 80% at or below 40 °C (upper limit de-rates to 45% relative humidity at 40 °C)

Electromagnetic compatibility: 2004/108/EC

Safety: UL3111-1, CSA1010.1, EN61010-1, IEC61010-1

Ordering information

For more detailed information about the DSA8300 Digital Serial Analyzer sampling oscilloscope, download theDSA8300 Digital Serial Analyzer, 80C00 Series Sampling Modules, 80E00 Series Sampling Modules, 80A00 Modules Specifications Technical Reference(Tektronix part number 077-0571-xx) from www.tek.com.

Models

DSA8300: Digital Serial Analyzer Sampling Oscilloscope

Standard accessories

071-2897-XX: DSA8300 Digital Serial Analyzer Quick Start User Manual
119-7083-XX: Keyboard
119-7054-XX: Mouse
200-4519-XX: Instrument front cover
016-1441-XX: Accessory pouch
119-6107-XX: Touch screen styluses (2)
006-3415-XX: ESD wrist strap with 6 foot coiled cord
063-4356-XX: DSA8300 Product Documentation CD
Not orderable: DSA8300 Online Help (part of application software)
Not orderable: DSA8300 Programmer Online Manual (part of application software)
020-3088-XX: DSA8300 TekScope Product Software Install Kit
Type dependent on selection during order placement: Power cord
013-0347-XX: VGA female to DVI male adapter

Instrument options

Options

ADVTRG: Add Advanced Trigger with Pattern Sync
80SSR4: 100GBASE-SR4 Comprehensive Transmitter compliance testing
80STDEC: 100GBASE-SR4 Transmitter and Dispersion Eye Closure (TDEC) testing
80S400G-TXO: PAM4 Optical transmitter compliance package. Also enables the TDECQ measurement feature in the 80SJNB opt. PAM4 opt. Advanced.
PAM4: PAM4 Transmitter Analysis software (requires option JNB01 (80SJNB Advanced) or option JNB02 (80SJNB Advanced with SDLA Visualizer) software)
CEI-VSR: OIF CEI 3.0 Compliance Solution for DSA8300
JNB: Add 80SJNB Essentials. Any version of 80SJNB also includes 80SJARB and the RIN/RINxOMA applications.
JNB01: Add 80SJNB Advanced
JNB02: Add 80SJNB Advanced with SDLA Visualizer
JARB: Add 80SJARB (included with Option JNB, JNB01, or JNB02)
ICMX: IConnect® and MeasureXtractor Signal Integrity and Failure Analysis Software
ICON: IConnect® Signal Integrity and Failure Analysis Software
SPAR: IConnect® S-parameters Software
DSA8300 400G-M4: 400G Optical Manufacturing Analysis Software, 4-channel TDECQ analysis. This software is designed for use on a PC connected to the DSA8300 sampling oscilloscope. (Customers who already have a DSA8300 will need to purchase DSA83UP 400G-M4.)

Power plug options

Opt. A0: North America power plug (115 V, 60 Hz)
Opt. A1: Universal Euro power plug (220 V, 50 Hz)
Opt. A2: United Kingdom power plug (240 V, 50 Hz)
Opt. A3: Australia power plug (240 V, 50 Hz)
Opt. A4: North America power plug (240 V, 50 Hz)
Opt. A5: Switzerland power plug (220 V, 50 Hz)
Opt. A6: Japan power plug (100 V, 50/60 Hz)
Opt. A10: China power plug (50 Hz)
Opt. A11: India power plug (50 Hz)
Opt. A12: Brazil power plug (60 Hz)
Opt. A99: No power cord

Language options

Opt. L0: English manual
Opt. L7: Simplified Chinese manual
Opt. L8: Traditional Chinese manual
Opt. L10: Russian manual

Language options include translated front-panel overlay for the selected language(s).

Service options

Opt. C3: Calibration Service 3 Years
Opt. C5: Calibration Service 5 Years
Opt. CA1: Single Calibration or Functional Verification
Opt. D1: Calibration Data Report
Opt. D3: Calibration Data Report 3 Years (with Opt. C3)
Opt. D5: Calibration Data Report 5 Years (with Opt. C5)
Opt. IF: Upgrade Installation Service
Opt. R3: Repair Service 3 Years (including warranty)
Opt. R5: Repair Service 5 Years (including warranty)

Probes and accessories are not covered by the oscilloscope warranty and Service Offerings. Refer to the datasheet of each probe and accessory model for its unique warranty and calibration terms.

DSA83UP - DSA8300 upgrade kit

ADVTRIG: Add Advanced Trigger with Pattern Sync
HDD8: Additional hard disk drive complete with assembled mounting bracket, operating system, and oscilloscope application
JARB: Add 80SJARB (included with Option JNB, JNB01, or JNB02)
JNB: Add 80SJNB Essentials
JNB01: Add 80SJNB Advanced
JNB02: Add 80SJNB Advanced with SDLA Visualizer
JNBTOJNB01: Upgrade from JNB to JNB Advanced
JNBTOJNB02: Upgrade from JNB to JNB Advanced with SDLA Visualizer
JNB01TOJNB02: Upgrade JNB01 to JNB02 (Adds SDLA Visualizer)
80SSR4: 100GBASE-SR4 Comprehensive Transmitter compliance testing (includes TDEC); recommend sampling modules 80C18 or 80C17, or 80C15 with Opt. CRTP
80STDEC: 100GBASE-SR4 Transmitter and Dispersion Eye Closure (TDEC); recommend sampling modules 80C18 or 80C17, or 80C15 with Opt. CRTP
80S400G-TXO: For PAM4 optical compliance tests and TDECQ measurement
PAM4: Upgrade 80SJNB: add PAM4 Transmitter Analysis capability; requires 80SJNB Advanced (JNB01) or 80SJNB Advanced+SDLA (JNB02) software
CEI-VSR: OIF CEI 3.0 Compliance Solution for DSA8300
DSA83UP 400G-M4: Upgrade for 400G Optical Manufacturing Analysis Software, 4-channel TDECQ analysis. For customers who already have a DSA8300.

DSA8300 Rack Mount

016-1791-02: DSA8300 Rack Mount Kit

Optional Accessories

Optical modules

Optical modules plug directly into the large slot of the DSA8300 sampling oscilloscope mainframe. See the80C00 Optical Modulesdatasheet for more details.

All optical modules have FC/PC connectors installed. Other connector adapters available as options are: ST/PC, D4/PC, Biconic, SMA 2.5, SC/PC, DIN/PC, HP/PC, SMA, DIAMOND 3.5.

80C07B: 2.5 GHz single-mode and multi-mode, amplified (750 to 1650 nm) optical module for multirate datacom and telecom applications w/ optional integrated clock recovery
80C08D: 9 GHz optical channel; single-mode and multi-mode, amplified (750 to 1650 nm) optical module optimized for 8.5 to 12.5 Gb/s applications with optional integrated clock recovery
80C10C: 55/70/80 GHz; single-mode (1290 to 1330 nm and 1520 to 1620 nm) optical module with reference receiver ¹ filters for multirate datacom and telecom 40 Gb/s and 100 Gb/s (4 × 25 Gb/s) and PAM4 50G/100G/200G/400G at 25+GBd and 53+GBd applications with optional calibrated trigger pick-off for use with external clock recovery instruments (such as the CR286A)
80C11B: 30 GHz, single-mode (100 to 1650 nm) optical module with reference receiver¹ filters for 8.5 to 14.1 Gb/s telecom and datacom standards. Optional, integrated clock recovery for 8.5 to 12.6 Gb/s applications
80C12B: 12 GHz optical channel; single-mode and multi-mode, amplified (750 to 1650 nm) optical module with optical reference receivers¹ to support 155 Mb/s to 12.5 Gb/s applications with calibrated trigger pick-off for use with external clock recovery instruments (such as the 80A05 or CR125A)
80C14: 12 GHz optical channel; single-mode and multi-mode, amplified (750 to 1650 nm) optical module optimized for 8.5 to 12.5 Gb/s applications with calibrated trigger pick-off for use with external clock recovery instruments (such as the CR175A or CR286A)
80C15: 32 GHz, single-mode and multi-mode optical module with bandwidth filters for multirate datacom and telecom 25, 100 (4x25) Gb/s, and PAM4 for 50G/100G/200G/400G applications. Option CRTP provides a second, high-sensitivity optical input to drive Clock Recovery Trigger Pickoff (CRTP) electrical differential outputs for clock recovery (using the Tektronix CR286A) or error detection functions (using the Tektronix PED4001).
80C17, 80C18: 32 GHz, single-mode and multi-mode, 1 and 2 channel, optical modules with bandwidth filters for multirate datacom and telecom 25, 100 (4x25) Gb/s, and PAM4 for 50G/100G/200G/400G applications.
80C20, 80C21: 53 GHz, single-mode, 1 and 2 channel, optical modules with bandwidth filters for multirate datacom and telecom 40, 100 (4x25) Gb/s, and PAM4 for 50G/100G/200G/400G applications.

¹Optical Reference Receiver (ORR) is a 4th-order Bessel-Thompson filter, with a nominal response and other details defined by standards. Details of the definition differ; Tektronix optimizes the response for best nominal fit and highest quality mask test results.

Electrical modules

Electrical modules plug directly into one of four small slots of the DSA8300 sampling oscilloscope mainframe. See the80E00 Electrical Sampling Modulesdatasheet for more details.

80E11: 70/60/40 ¹ GHz electrical sampler, dual channel
80E11X1: 70/60/40¹ GHz electrical sampler, single channel
80E10B: Remote ² Sampling Module – 50/40/30¹ GHz electrical, dual-channel with true-differential TDR capabilities
80E09B: Remote² Sampling Module – 60/40/30¹ GHz electrical, dual-channel
80E08B: Remote² Sampling Module – 30/20¹ GHz electrical, dual-channel with true-differential TDR capabilities
80E07B: Remote² Sampling Module – 30/20¹ GHz electrical, dual-channel
80E04: 20 GHz electrical sampler, dual-channel with true-differential TDR capabilities. For remote sampling use the 80X01 or 80X02 Electrical Sampling Module Extender Cables
80E03: 20 GHz electrical sampler, dual-channel. For remote sampling use the 80X01 or 80X02 Electrical Sampling Module Extender Cables

¹User-selectable bandwidth.

²Each remote sampler/TDR generator is on a separate 2-meter remote cable for easy co-location with the device under test and best acquired signal fidelity.

Phase reference module

The 82A04B Phase Reference module, when installed in the DSA8300 and provided with a clock synchronous with the data to be acquired, provides a very low-jitter time base for acquiring signals from the device under test. It can accommodate clocks from 2 GHz ¹ to >60 GHz.

82A04B: Phase Reference Module – Standard module supports clocks up to 32 GHz. With Option 60G it supports clocks to >60 GHz

¹For clock frequencies <8 GHz, it may be necessary to filter the clock input to eliminate harmonics from the clock signal (see Other Accessories 020-2566-xx, 020-2567-xx, and 020-2568-xx).

Clock recovery module/instrument

CR125A: Electrical Clock Recovery instrument. CR125A recovers clocks from serial data streams for all of the most common electrical standards in the continuous 100 Mb/s to 12.5 Gb/s range. Applicable to electrical signals and for 80C12B
CR175A: Electrical Clock Recovery instrument. CR175A recovers clocks from serial data streams for all of the most common electrical standards in the continuous 100 Mb/s to 17.5 Gb/s range. Applicable to electrical signals and for 80C12B and 80C14
CR286A-HS: Electrical Clock Recovery instrument. CR286A recovers clocks from serial data streams for all of the most common electrical standards in the continuous 100 Mb/s to 28.6 Gb/s range. Applicable to electrical signals and for 80C12B, 80C14, and 80C10B/80C10C (for rates up to 28.6 Gb/s). Note: Option HS (High Sensitivity) is needed for most usage.

Product bundle for 10-28 Gb/s applications

80B28G: Product bundle which includes one each of the following products: 80E09B Electrical Sampling Module; 82A04B Phase Reference Module; CR286A-HS 28.6 GHz Clock Recovery instrument; 80X01: 1-meter sampling module extender cable; and 80A08 28 Gb/s Measurements Accessory Kit.

Recommended Accessories

80A09: 26 GHz ESD Protection Device (in-line always active)
80A02: EOS/ESD isolation module for electrical static isolation of electrical sampling modules
80A03: TEKConnect probe interface module
80A08: Accessory kit for electrical measurements up to 28 Gb/s; includes electrical trigger pick-off with cables for CRU, all in 2.4 mm.
80X01: 1-meter electrical sampling module extender cable
80X02: 2-meter electrical sampling module extender cable

Calibration kits and accessories (3rd party)

For best S-parameter measurement results with the 80E10B, 80E08B, and 80E04 electrical TDR modules and IConnect® software, we recommend precision calibration kits, adapter kits, connector savers, airlines, torque wrenches, and connector gauges from Maury Microwave.

These components are compatible with the 2.92 mm, 2.4 mm, and 1.85 mm connectors of the 80E00 modules. Contact Maury Microwave (www.maurymw.com/tektronix.htm) to order calibration kits and other components.

DSA8300 Datasheet

Digital Serial Analyzer Sampling Oscilloscope

Replacement Products

更多資訊

Notice to EU customers

Key performance specifications

Key features

Applications

Superior performance with extraordinary versatility

Measurement and analysis tools for optical testing applications

Test solutions

80B28G - a DSA8300 product bundle for 28 Gb/s applications

Specifications

Vertical system

Horizontal system

Trigger system

Acquisition system

Waveform measurements

Display system

Input output ports

Data storage

Computer system

Power source

Physical characteristics

EMC, environment and safety

Ordering information

Models

Standard accessories

Instrument options

Options

Power plug options

Language options

Service options

DSA83UP - DSA8300 upgrade kit

DSA8300 Rack Mount

Optional Accessories

Optical modules

Electrical modules

Phase reference module

Clock recovery module/instrument

Product bundle for 10-28 Gb/s applications

Recommended Accessories

Calibration kits and accessories (3rd party)