ダウンロード

マニュアル、データシート、ソフトウェアなどのダウンロード:

ダウンロード・タイプ
型名またはキーワード

フィードバック

Arbitrary Waveform Generators

AWGSYNC01 Synchronization Hub Datasheet

詳細情報

オンラインで読む:

AWGSYNC01 EN US 76W 30652 2

The AWGSYNC01 enables the multi-instrument synchronization of up to four AWG70001A or AWG70002A units allowing up to eight channels to be aligned to the same clock, pattern jump and trigger inputs. The AWGSYNC01 requires no additional software and allows for the rapid and consistent synchronization of multiple devices. The AWGSYNC01 provides calibration ports to deskew up to four AWG70000 instruments to within ±10ps. After the deskew process the AWGSYNC01 can repeatedly return to within ≤5 ps of the same deskew point.

Key performance specifications

  • Random Jitter (typical): 315 fsRMS
  • Total jitter (typical): 13 psp-p at 12.5 Gb/s
  • Instrument to instrument skew: ±10 ps
  • Skew repeatability/accuracy: ≤5 ps

Key features

  • Synchronize signal output from two to four AWG70000 instruments (providing two to eight signal outputs)
  • Synchronize to within ±10 ps
  • Trigger all channels to the same resolution

Applications

  • Wideband RF/MW for communications and defense electronics
  • Validation and compliance testing of high speed silicon and communications devices
  • Coherent optical research
  • Leading edge research in electronics, physics and chemistry

High speed serial

For high-speed serial applications the AWG70000A Series offers the industry's best solution for addressing challenging signal stimulus issues faced by digital designers who need to verify, characterize, and debug complex digital designs. The file-based architecture uses direct synthesis to create complex data streams and gives users a simple, repeatable, and flexible way to solve the toughest signal generation challenges in high-speed serial communication applications. The AWGSYNC01 lets users synchronize multiple AWG instruments to output signals for complex or multi-lane standards such as HDMI and MIPI.

Coherent optical

Today's high speed and increasingly Web-driven world is pushing the demand for short and long haul coherent optical development. Phase modulation, high baud rate, high sample rate, bandwidth, and resolution are all critical to optical applications. Tektronix understands the challenges and inconsistencies of coherent optical testing and offers a reliable, easy to set up and high performance tool set for optical testing, waveform generation and calibration.

Generating the desired signal is only the first challenge in coherent optical. The quality of the signal, low EVM's, and having a clear, open eye is crucial. Complex quadrature modulations, such as PAM-4, require synchronized output from multiple AWG70000 instruments.

The AWGSYNC01 can synchronize multiple single-channel AWG70000 instruments, at the maximum 50 Gs/s sample rate, to output synchronized baseband signals with low EVM and 32 Gbaud performance. The AWGSYNC01 streamlines the complex multiple instrument signal synchronization alignment process, resulting in synchronized signals with a high rate of repeatability and with low jitter.

Research applications

Advanced research applications such as quantum computing, mass spectroscopy, MEMS, NEMS, and particle physics often demand the precise alignment of multiple simultaneous triggering, precompensation, or I/Q generation signals, all with low jitter. AWG70000 series instruments, used with the AWGSYNC01 Synchronization Hub, provide fast and repeatable results. Day to day experimental setups require no additional equipment for synchronization.

The AWGSYNC01 comes with all required phase-stable and delay-matched calibration and clock cabling needed to start synchronizing straight out the box. You can use the clock out signal from the Master AWG70000 instrument to synchronize the output signals, or use an external clock reference signal for higher precision when needed.

Performance you can count on

Depend on Tektronix to provide you with performance you can count on. In addition to industry-leading service and support, this product comes backed by a standard one-year warranty.

Specifications

All specifications are guaranteed unless noted otherwise. All specifications apply to all models unless noted otherwise.

General specifications

Jitter
Random Jitter (typical)
315 fs RMS
Total jitter (typical)
13 psp-p at 12.5 Gb/s
Skew
Instrument to instrument skew (typical)
±10 ps
Skew repeatability/accuracy (typical)
≤5 ps

After changes of sample rate or power cycle and within ±5 °C from deskew calibration.

Inputs, outputs

Calibration Ports
Four SMA type connectors used to deskew the instrument signal delays. Only use the supplied matched silver calibration cables with these connectors when deskewing the AWG70000 instrument signal outputs.
Trigger Inputs (A, B)
External trigger inputs
Connector
SMA
Number of trigger inputs
2
Impedance
50 Ω or 1 kΩ selectable
Polarity
Positive or negative selectable
Input voltage range
50 Ω: <5 VRMS

1 kΩ: ±10 VRMS

Threshold range
-5.0 V to 5.0 V
Threshold resolution
0.1 V
Minimum trigger pulse width (typical)
20 ns
Trigger holdoff
>18 μs
Trigger delay to analog output (typical)
Asynchronous trigger mode: 32,480 / (2 * fclk) ±20 ns

Synchronous trigger mode: 30,880 / (2 * fclk) ±20 ns

fclk is the frequency of the DAC sampling clock

The DAC sampling clock frequency is displayed on the clock settings tab when the external clock output is enabled.

Trigger asynchronous jitter (typical)
80/sampling clock frequency

The asynchronous jitter performance is directly proportional the sync clock out frequency. The sync clock out is derived from the DAC sampling clock. The DAC sampling clock frequency is displayed on the clock settings tab when the external clock output is enabled.

Trigger synchronous jitter (typical)
Clock In = 12.5 GHz: 300 fsRMS, 4.2 ps RJp-p BER@10-12

Variable Reference In = 156.25 MHz: 400 fsRMS, 5.6 ps RJp-p BER@10-12

Fixed Reference In = 10 MHz: 1.7 psRMS, 23.8 ps RJp-p BER@10-12

Sample rate = 25 GS/s

Sync to AWG (1-4)
Communication ports used by to synchronize all connected AWG70000 instruments. The AWG70000 connected to Port 1 is the Master AWG70000, which sets up and controls synchronization of the connected instruments. You must connect an AWG70000 to Port 1. AWG70000 instruments connected to Ports 2 through 4 are Slave AWG70000 instruments.

Use the supplied orange cable assemblies to connect these ports to the AWG70000 instruments.

Clock in from Master AWG
Synchronizing clock signal input from the master AWG70000 Clock Out port, or from an external clock signal source.
Connector
SMA
Input impedance
50 Ω, AC coupled
Input frequency range
6.25 GHz to 12.5 GHz
Input amplitude (typical)
+5 dBm to +10 dBm
Clock Out to AWG Clock In
Connector
SMA
Impedance
50 Ω, AC coupled
Frequency range
6.25 GHz to 12.5 GHz
Output amplitude (typical)
+5 dBm to +10 dBm
Sync Clock Out
Connector
SMA
Impedance
50 Ω, AC coupled
Frequency
10 MHz ±(1 ppm + aging)
Output amplitude (typical)
1.0 V ±150 mVp-p
Pattern Jump In
Number of jump destinations
256
Connector
15-pin D-sub female connector on rear panel
Input levels
3.3 V LVCMOS

5 V TTL compliant (input impedance pull up to 5 V by 1 kΩ resistor)

Strobe
Polarity: Data is clocked in on negative edge

Minimum pulse width: (typical) 64 ns

Latency to analog output (typical)
102,125/fclk +20 ns ± 20 ns

The DAC sampling clock frequency is displayed on the clock settings tab when the external clock output is enabled

Holdoff time (typical)
>18 μs

Strobe hold off is the amount of delay required at the end of a waveform before another strobe pulse can be processed

Connector pin/signal assignment
AWGSYNC01 EN US 76W 30652 2
Pin Signal
1, 6, 8, 9, 14, 15 GND
2 Data bit 0, input
3 Data bit 1, input
4 Data bit 2, input
5 Data bit 3, input
7 Strobe input
10 Data bit 4, input
11 Data bit 5, input
12 Data bit 6, input
13 Data bit 7, input

Physical characteristics

Dimensions
Height
44.45 mm (1.75 in)
Width
460.5 mm (18.13 in)
Depth
603 mm (23.76 in)
Weight
Instrument only
5.4 kg (12 lb)
With packaging
9.1 kg (20 lb)
Cooling clearance
Top, bottom, left, right
0 mm (0 in)
Rear
50 mm (2 in)
Power
AC line input
100 to 240 V AC, 50/60 Hz
Consumption
110 W

Environment

Temperature
Operating
0 °C to +50 °C (+32 °F to +122 °F)
Nonoperating
-20 °C to +60 °C (-4.0 °F to +140 °F)
Humidity
Operating (noncondensing)
5% to 90% relative humidity (% RH) at up to 30 °C

5% to 45% relative humidity above 30 °C up to 50 °C

Nonoperating (noncondensing)
5% to 90% relative humidity (% RH) at up to 30 °C

5% to 45% relative humidity above 30 °C up to 60 °C

Altitude
Operating
Up to 3,000 meters (9,843 feet)

Derate maximum operating temperature by 1 °C per 300 meters above 1500 meters

Nonoperating
Up to 12,000 meters (39,370 feet)
Regulatory
Safety
UL61010-1, CAN/CSA-22.2, No.61010-1, EN61010-1, IEC61010-1
EMC Emissions
IEC61326, EN55011 (Class A), IEC61000-3-2, IEC61000-3-3
EMC Immunity
IEC61326, IEC61000-4-2/3/4/5/6/11
Regional certifications
Europe: EN61326

Australia/New Zealand: AS/NZS 2064

Ordering information

Models

AWGSYNC01
Synchronizes signal output on up to four AWG70001A and/or AWG70002A instruments

Standard Accessories

071-3292-xx
AWGSYNC01 Safety and Installation Instructions
174-6157-xx
AWG synchronization communication cable (orange)
174-6568-xx
Phase stable clock cable (blue)
174-6606-xx
Calibration deskew cables (set of 4 cables, silver)
Power cord
Specify power cord option at time of order

Warranty

One year parts and labor

Standard Accessories

071-3292-xx
AWGSYNC01 Safety and Installation Instructions
174-6157-xx
AWG synchronization communication cable (orange)
174-6568-xx
Phase stable clock cable (blue)
174-6606-xx
Calibration deskew cables (set of 4 cables, silver)
Power cord
Specify power cord option at time of order

Warranty

One year parts and labor

Options

Power plug options

Opt. A0
North America power plug (115 V, 60 Hz)
Opt. A1
Universal Euro power plug (220 V, 50 Hz)
Opt. A2
United Kingdom power plug (240 V, 50 Hz)
Opt. A3
Australia power plug (240 V, 50 Hz)
Opt. A5
Switzerland power plug (220 V, 50 Hz)
Opt. A6
Japan power plug (100 V, 50/60 Hz)
Opt. A10
China power plug (50 Hz)
Opt. A11
India power plug (50 Hz)
Opt. A12
Brazil power plug (60 Hz)
Opt. A99
No power cord

Service options

Opt. C3
Calibration Service 3 Years
Opt. C5
Calibration Service 5 Years
Opt. R3
Repair Service 3 Years (including warranty)
Opt. R3DW

Repair Service Coverage 3 Years (includes product warranty period). 3-year period starts at time of instrument purchase

Opt. R5
Repair Service 5 Years (including warranty)
Opt. R5DW

Repair Service Coverage 5 Years (includes product warranty period). 5-year period starts at time of instrument purchase

Opt. S1
On-site Service 1 Year
Opt. S3
On-site Service 3 Years (with R or C options)

Cables and accessories are not covered by the instrument warranty and Service Offerings.

Recommended accessories

AWGRACK
Rack mount kit for AWG70000A Series instruments and AWGSYNC01