연락처
텍트로닉스 담당자와 실시간 상담 6:00am-4:30pm PST에 이용 가능
전화 문의
9:00am-6:00PM KST에 이용 가능
다운로드
매뉴얼, 데이터 시트, 소프트웨어 등을 다운로드할 수 있습니다.
피드백
USB 3.2 Transmitter Solutions
USBSSP-TX, USB-TX Datasheet
The Tektronix USBSSP-TX and USB-TX Automated Transmitter solutions provide an easy way to validate and characterize emerging USB 3.2 Type-C host controllers, hubs and devices with Tektronix MSO/DPO/70000DX/SX series oscilloscopes.
Key Offerings
- Transmitter testing
- Provides a comprehensive automated and manual toolset for USB 3.2 Gen1 (5 Gbps) and Gen2 (10 Gbps) verification, characterization, debug, and compliance test.
- Supports Type-C, Standard and Micro connectors for USB 3.2 Specification.
- Provides automatic processing of USB-IF SIGTEST results without manual intervention.
- Auto selection of sources (channels) based on the probe type selected.
- Includes support for captive devices and their associated channels as per CTS.
- Uses pre-recorded mode to run measurements for offline analysis and collaboration with the globally dispersed teams.
- DPOJET plugin for USB 3.2 Type-C, Standard and Micro connectors which supports USB 3.2 specification and CTS (Gen1 & Gen2) with setup files and MOI.
- Automatic DUT control and pattern validation to capture all required data patterns (CP0, CP1, CP9, CP10, etc.).
- Support embedding all Channels and their respective filter files for Type-C, Standard and Micro Connectors using SDLA .
- Quickly validate test status with comprehensive reporting that details test margins, pass/fail results, and plots in PDF, MHT and CSV formats.
- Manual Lane Switching – Support for reversible Type-C connector.
Applications
USB transmitter testing
- Host and Device silicon validation
- System, peripheral, and hub validation and integration
- Manufacturing test
Complete automation for USB testing
The automated solution for USB 3.2 simplifies transmitter testing. No longer is it a requirement that the end user be an expert in USB. The process of defining test parameters, power on/off DUT, capturing the LFPS signal, toggling the compliance patterns, making sure the compliance pattern captured is correct, showing results after each measurement is executed, and saving the test results, is fully automated in the Tektronix USB 3.2 automated test solution.
Required test procedures (MOI) can be found at: www.tek.com/usb.
Ordering Information
Key differences between USB-TX and USBSSP-TX
| Feature | USB-TX | USBSSP-TX1 |
|---|---|---|
| Automatic measurement selections based on device type, test type, test points, and selected probes | X | X |
| Automatic selection of receiver CTLE filter | CTLE only | CTLE/DFE |
| Automatic selection of Tx channel modeling for software channel emulation | X | X |
| Complete coverage of USB 3.2 Normative and Informative tests (see next table) | Gen1 (5 Gb/s) | Gen1 (5 Gb/s) and Gen2 (10 Gb/s) |
| Automatically save test reports and waveforms | X | X |
| Re-analyze prerecorded waveforms | X | X |
| Single test report for all measurements | Gen1 (5 Gb/s) | Gen1 (5 Gb/s) and Gen2 (10 Gb/s) |
| Automated LFPS measurements (setup files only) | X | X |
| Automated DUT toggle | X | X |
| Automated SIGTEST measurements | X | X |
Automated TekExpress USB 3.2 (5 Gb/s and 10 Gb/s) transmitter measurements
- DPO/MSO700002
- Tektronix DPO (Digital Phosphor Oscilloscope) or MSO (Mixed Signal Oscilloscope) Oscilloscopes – 16 GHz and above with DPOJET and SDLA64 installed
- DPO/MSO70000 Opt. USBSSP-TX3
- USB 3.2 5 and 10 Gb/s Transmitter Normative and Informative Tests for TekExpress Automated Compliance Test Software
- USBSSP-UP
- Upgrade USB-TX (Supports 5G only) software to USBSSP-TX software package (Supports 5G & 10G)
- DPOFL-USBSSP-TX3
- Floating license upgrade for USB 3.2 5 Gb/s and 10 Gb/s Transmitter Normative and Informative Tests for TekExpress Automated Compliance Test Software
- DPO-UP USBSSP-TX
- Upgrade for USB 3.2 5 Gb/s and 10 Gb/s Transmitter Normative and Informative Tests for TekExpress Automated Compliance Test Software
- DPOFL-USBSSP-UP
- Upgrade from Floating USB TX to Floating USB SSP TX
| Item | Vendor | Quantity |
|---|---|---|
| USB3ET Type A and Micro B Gen1 test fixtures | USB-IF | 1 |
| USB31AET Type A & Micro B Gen2 test fixture kit | USB-IF | 1 |
| USB31CET Type C Gen1 and Gen2 test fixture | USB-IF | 1 |
| PMCABLE1M Phase Matched SMA cable set | Tektronix | 2 |
| AFG3k or AFG31k 50MHz or higher, AWG5000C, AWG5200, AWG7000C or AWG70000 (DUT State Control) | Tektronix | 1 |
| 015-0572-00 BNC to SMA adapter | Tektronix | 2 |
| PWS4000 Tektronix Power Supply (optional for automatic power cycling) | Tektronix | 1 |
Automated TekExpress USB 3.2 (5 Gb/s) transmitter measurements
- DPO/MSO700002
- Tektronix DPO (Digital Phosphor Oscilloscope) or MSO (Mixed Signal Oscilloscope) Oscilloscopes – 12.5 GHz and above with DPOJET and SDLA64 installed
- DPO/MSO70000 Opt. USB-TX4
- USB 3.2 5 Gb/s Transmitter Normative and Informative Tests for TekExpress Automated Compliance Test Software
- DPOFL-USB-TX4
- Floating license upgrade for USB 3.2 5 Gb/s Transmitter Normative and Informative Tests for TekExpress Automated Compliance Test Software
- DPO-UP USB-TX4
- Upgrade for USB 3.2 5 Gb/s Transmitter Normative and Informative Tests for TekExpress Automated Compliance Test Software
- USB-TX-UP
- Upgrade USB TX solution from dongle based license to software node locked license.
| Item | Vendor | Quantity |
|---|---|---|
| USB3ET Type A & Micro B Gen1 test fixture kit | USB-IF | 1 |
| USB31CET Type C test fixture kit | USB-IF | 1 |
| PMCABLE1M Phase Matched SMA cable set | Tektronix | 2 |
| AFG3k or AFG31k 50MHz or higher, AWG5000C, AWG7000C or AWG70000 (DUT State Control) | Tektronix | 1 |
| 015-0572-00 BNC to SMA adapter | Tektronix | 2 |
Prerequisite host system software requirements
- For USBSSP-TX and USB-TX
- DPO/MSO70000 Series oscilloscope with Microsoft Windows 10
Required equipment for USB 3.2 testing
For complete list of required equipment's, go to https://www.tek.com/usb.
1 USB-TX option is not a prerequisite
2 Requires scope BW ≥16GHz for USB 3.2 Gen2 (10Gbps) and ≥12.5 GHz for USB 3.2 Gen1 (5Gbps).
3 Requires DPOJET Jitter and Eye Analysis Tools (Opt. DJA) and ≥16 GHz oscilloscope and SDLA Visualizer (SDLA64).
4 Requires oscilloscope with bandwidth ≥12.5 GHz and DPOJET Jitter and Eye Analysis Tools (Opt. DJA).
Tektronix is ISO 14001:2015 and ISO 9001:2015 certified by DEKRA. 55W-23929-23
