Mixed Domain Oscilloscopes

Hardware bandwidth limits

≥350 MHz models

20 MHz or 250 MHz

200 MHz models

20 MHz

Input coupling

AC, DC

Input impedance

1 MΩ ±1% (13 pF), 50 Ω ±1%

Input sensitivity range

1 MΩ

1 mV/div to 10 V/div

50 Ω

1 mV/div to 1 V/div

Vertical resolution

8 bits (11 bits with Hi Res)

Maximum input voltage

1 MΩ

300 V_RMS CAT II with peaks ≤ ±425 V

50 Ω

5 V_RMS with peaks ≤ ±20 V

DC gain accuracy

±1.5% (±2.0% at 1mV/div), derated at 0.10%/°C above 30 °C

±3.0% for variable gain, derated 0.10%/°C above 30 °C

Offset accuracy

±(0.005 * |offset - position| + DC Balance)

DC balance

0.1 div with DC - 50Ω scope input impedance (50Ω BNC terminated)

Channel-to-channel isolation (typical)

Any two channels at equal vertical scale ≥100:1 at ≤100 MHz and ≥30:1 at >100 MHz up to the rated bandwidth

Random noise (typical)

Vertical scale setting	50 Ω, RMS
	MDO4104C (all configurations)	MDO40x4C (with option SA3 or SA6)	MDO40x4C (without option SA3 or SA6)
1 mV/div	0.093 mV	0.084 mV	0.163 mV
100 mV/div	3.31 mV	2.37 mV	2.01 mV
1 V/div	24.27 mV	20.62 mV	20.51 mV

Offset range

Volts/div setting	Offset range
	1 M Ω input	50 Ω input
1 mV/div to 50 mV/div	±1 V	±1 V
50.5 mV/div to 99.5 mV/div	±0.5 V	±0.5 V
100 mV/div to 500 mV/div	±10 V	±10 V
505 mV/div to 995 mV/div	±5 V	±5 V
1 V/div to 10 V/div	±100 V	±5 V
5.05 V/div to 10 V/div	±50 V	NA

Time base range

1 GHz models (without option SA3 or SA6) and 1 GHz models (with option SA3 or SA6 with 2 channels enabled)

400 ps to 1000 s

≤ 500 MHz models and 1 GHz models (with option SA3 or SA6 and 4 channels enabled)

1 ns to 1000 s

Maximum duration at highest sample rate (all/half channels)

1 GHz models (without option SA3 or SA6) and 1 GHz models (with option SA3 or SA6 with 2 channels enabled)

8/4 ms

≤ 500 MHz models and 1 GHz models (with option SA3 or SA6 and 4 channels enabled)

8/8 ms

Time-base delay time range

-10 divisions to 5000 s

Channel-to-channel deskew range

±125 ns

Time base accuracy

±5 ppm over any ≥1 ms interval

Trigger modes

Auto, Normal, and Single

Trigger coupling

DC, AC, HF reject (attenuates >50 kHz), LF reject (attenuates <50 kHz), noise reject (reduces sensitivity)

Trigger holdoff range

20 ns to 8 s

Trigger sensitivity

Internal DC coupled

1 mV/div to 4.98 mV/div

1.8 div

5 mV/div to 9.98 mV/div

0.6 div

10 mV/div to 19.98 mV/div

1.2 div

≤20 mV/div

0.5 div

Trigger level ranges

Any input channel

±8 divisions from center of screen, ±8 divisions from 0 V when vertical LF reject trigger coupling is selected

Line

The line trigger level is fixed at about 50% of the line voltage.

Trigger frequency readout

Provides 6-digit frequency readout of triggerable events.

Trigger types

Edge

Positive, negative, or either slope on any channel. Coupling includes DC, AC, HF reject, LF reject, and noise reject.

Sequence (B-trigger)

Trigger Delay by Time: 8 ns to 8 s. Or Trigger Delay by Events: 1 to 4,000,000 events. Not available when “Either” edge is selected.

Pulse Width

Trigger on width of positive or negative pulses that are >, <, =, ≠, or inside/outside a specified period of time.

Timeout

Trigger on an event which remains high, low, or either, for a specified time period (4 ns to 8 s).

Runt

Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again.

Logic

Trigger when any logical pattern of channels goes false or stays true for specified period of time. Any input can be used as a clock to look for the pattern on a clock edge. Pattern (AND, OR, NAND, NOR) specified for all input channels defined as High, Low, or Don’t Care.

Setup and Hold

Trigger on violations of both setup time and hold time between clock and data present on any of the analog and digital input channels.

Setup and hold trigger type	Description
Setup Time Range	-0.5 ns to 1.024 ms
Hold Time Range	1.0 ns to 1.024 ms
Setup + Hold Time Range	0.5 ns to 2.048 ms

Rise/Fall Time

Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either and time range is 4.0 ns to 8 s.

Video

Trigger on all lines, odd, even, or all fields on NTSC, PAL, and SECAM video signals.

Custom bi-level and tri-level sync video standards.

Extended Video (optional)

Trigger on 480p/60, 576p/50, 720p/30, 720p/50, 720p/60, 875i/60, 1080i/50, 1080i/60, 1080p/24, 1080p/24sF, 1080p/25, 1080p/ 30, 1080p/50, 1080p/60, and custom bi-level and tri-level sync video standards.

Custom bi-level and tri-level sync video standards.

Parallel (requires option MDO4MSO)

Trigger on a parallel bus data value. Parallel bus can be from 1 to 20 bits (from the digital and analog channels) in size. Binary and Hex radices are supported.

Acquisition modes

Sample

Acquire sampled values.

Peak Detect

Captures glitches as narrow as 800 ps (MDO4104C with option SA3 or SA6 and ≤ 2 channels enabled or MDO4104C without SA3 or SA6) or 1.6 ns MDO4104C with option SA3 or SA6 and ≥ 3 channels enabled and all other models) at all sweep speeds

Averaging

From 2 to 512 waveforms included in average.

Envelope

Min-max envelope reflecting Peak Detect data over multiple acquisitions. Number of waveforms in the envelope selectable between 1 and 2000 and infinity

Hi Res

Real-time boxcar averaging reduces random noise and increases vertical resolution.

Roll

Scrolls waveforms right to left across the screen at sweep speeds slower than or equal to 40 ms/div.

FastAcq®

FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events, capturing >340,000 wfms/s on 1 GHz models and >270,000 wfms/s on 200 MHz - 500 MHz models.

Cursors

Waveform and Screen

DC measurement accuracy

±((DC Gain Accuracy) * |reading - (Offset - Position)| + Offset Accuracy + 0.15 div + 0.6 mV)

Automatic measurements (time domain)

30, of which up to eight can be displayed on-screen at any one time. Measurements include: Period, Frequency, Delay, Rise Time, Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive Overshoot, Negative Overshoot, Total Overshoot, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle RMS, Positive Pulse Count, Negative Pulse Count, Rising Edge Count, Falling Edge Count, Area and Cycle Area.

Automatic measurements (frequency domain)

3, of which one can be displayed on-screen at any one time. Measurements include Channel Power, Adjacent Channel Power Ratio (ACPR), and Occupied Bandwidth (OBW)

Measurement statistics

Mean, Min, Max, Standard Deviation.

Reference levels

User-definable reference levels for automatic measurements can be specified in either percent or units.

Gating

Isolate the specific occurrence within an acquisition to take measurements on, using either the screen or waveform cursors.

Waveform histogram

A waveform histogram provides an array of data values representing the total number of hits inside of a user-defined region of the display. A waveform histogram is both a visual graph of the hit distribution as well as a numeric array of values that can be measured.

Sources

Channel 1, Channel 2, Channel 3, Channel 4, Ref 1, Ref 2, Ref 3, Ref 4, Math

Types

Vertical, Horizontal

Waveform histogram measurements

12, of which up to eight can be displayed on-screen at any one time. Waveform Count, Hits in Box, Peak Hits, Median, Max, Min, Peak-to-Peak, Mean, Standard Deviation, Sigma 1, Sigma 2, Sigma 3 

Arithmetic

Add, subtract, multiply, and divide waveforms.

Math functions

Integrate, differentiate, FFT

FFT

Spectral magnitude. Set FFT Vertical Scale to Linear RMS or dBV RMS, and FFT Window to Rectangular, Hamming, Hanning, or Blackman-Harris.

Spectrum math

Add or subtract frequency-domain traces.

Advanced math

Define extensive algebraic expressions including waveforms, reference waveforms, math functions (FFT, Intg, Diff, Log, Exp, Sqrt, Abs, Sine, Cosine, Tangent, Rad, Deg), scalars, up to two user-adjustable variables and results of parametric measurements (Period, Freq, Delay, Rise, Fall, PosWidth, NegWidth, BurstWidth, Phase, PosDutyCycle, NegDutyCycle, PosOverShoot, NegOverShoot, TotalOverShoot, PeakPeak, Amplitude, RMS, CycleRMS, High, Low, Max, Min, Mean, CycleMean, Area, CycleArea, and trend plots). For example, (Intg(Ch1 - Mean(Ch1)) × 1.414 × VAR1)

Events

None, when a trigger occurs, or when a defined number of acquisitions complete (1 to 1,000,000)

Actions

Stop acquisition, save waveform to file, save screen image, print, AUX OUT pulse, remote interface SRQ, e-mail notification, and visual notification

Repeat

Repeat the act on event process (1 to 1,000,000 and infinity)

Sources

Channel 1, Channel 2, Channel 3, Channel 4 

Video standards

NTSC, PAL

Contrast and brightness

Manual and automatic

Field selection

Odd, Even, Interlaced

Picture location on screen

Selectable X and Y location, width and height adjustment, start line and pixel and line-to-line offset control.

Power quality measurements

V_RMS, V_{Crest Factor}, Frequency, I_RMS, I_{Crest Factor}, True Power, Apparent Power, Reactive Power, Power Factor, Phase Angle.

Switching loss measurements

Power loss

T_on, T_off, Conduction, Total.

Energy loss

T_on, T_off, Conduction, Total.

Harmonics

THD-F, THD-R, RMS measurements. Graphical and table displays of harmonics. Test to IEC61000-3-2 Class A and MIL- STD-1399, Section 300A.

Ripple measurements

V_Ripple and I_Ripple.

Modulation analysis

Graphical display of +Pulse Width, -Pulse Width, Period, Frequency, +Duty Cycle, and -Duty Cycle modulation types.

Safe operating area

Graphical display and mask testing of switching device safe operating area measurements.

dV/dt and dI/dt measurements

Cursor measurements of slew rate

Included standard masks¹

ITU-T, ANSI T1.102, USB

Test source

Limit test: Any Ch1 - Ch4 or any R1 - R4

Mask test: Any Ch1 - Ch4

Mask creation

Limit test vertical tolerance from 0 to 1 division in 1 m division increments; Limit test horizontal tolerance from 0 to 500 m division in 1 m division increments

Load standard mask from internal memory

Load custom mask from text file with up to 8 segments

Mask scaling

Lock to Source ON (mask automatically re-scales with source-channel settings changes)

Lock to Source OFF (mask does not re-scale with source-channel settings changes)

Test criteria run until

Minimum number of waveforms (from 1 to 1,000,000 and Infinity)

Minimum elapsed time (from 1 second to 48 hours and Infinity)

Violation threshold

From 1 to 1,000,000 

Actions on test failure

Stop acquisition, save screen image to file, save waveform to file, print screen image, trigger out pulse, set remote interface SRQ

Actions on test complete

Trigger out pulse, set remote interface SRQ

Results display

Test status, total waveforms, number of violations, violation rate, total tests, failed tests, test failure rate, elapsed time, total hits for each mask segment

Span

1 kHz - 3 GHz (models with option SA3) or 1 kHz - 6 GHz (models with option SA6)

Span adjustable in a 1-2-5 sequence

Variable resolution = 1% of the next span setting

Resolution bandwidth range

The resolution bandwidth range for windowing functions is as follows:

Kaiser (default): 20 Hz - 200 MHz

Rectangular: 10 Hz - 200 MHz

Hamming: 10 Hz - 200 MHz

Hanning: 10 Hz - 200 MHz

Blackman-Harris: 20 Hz - 200 MHz

Flat-top: 30 Hz - 200 MHz

Adjusted in a 1-2-3-5 sequence

RBW shape factor (Kaiser)

60 dB / 3 dB shape factor: ≥ 4:1

Reference level

Setting range: -140 dBm to +30 dBm in steps of 1 dB

Input vertical range

Vertical measurement range: +30 dBm to DANL

Vertical setting of 1 dB/div to 20 dB/div in a 1-2-5 sequence

Vertical position

-100 divs to +100 divs

Vertical units

dBm, dBmV, dBµV, dBµW, dBmA, dBµA

Displayed average noise level (DANL)

Frequency range	DANL
9 kHz - 50 kHz	< -116 dBm/Hz (< -123 dBm/Hz, typical)
50 kHz – 5 MHz	< -130 dBm/Hz (< -141 dBm/Hz, typical)
5 MHz - 400 MHz	< -146 dBm/Hz (< -150 dBm/Hz, typical)
400 MHz - 3 GHz	< -147 dBm/Hz (< -150 dBm/Hz, typical)
3 GHz - 4 GHz (models with option SA6 only)	< -148 dBm/Hz (< -151 dBm/Hz, typical)
4 GHz - 6 GHz (models with option SA6 only)	< -140 dBm/Hz (< -145 dBm/Hz, typical)

DANL with TPA-N-PRE preamp attached

Preamp set to "Auto", and Reference Level set to -40 dB

The DANL of the MDO4000C with the preamp in the Bypass state is ≤3 dB higher than the DANL of the MDO4000C without the preamp.

Frequency range	DANL
9 kHz - 50 kHz	< -119 dBm/Hz (< -125 dBm/Hz, typical)
50 kHz – 5 MHz	< -140 dBm/Hz (< -146 dBm/Hz, typical)
5 MHz - 400 MHz	< -156 dBm/Hz (< -160 dBm/Hz, typical)
400 MHz - 3 GHz	< -157 dBm/Hz (< -160 dBm/Hz, typical)
3 GHz - 4 GHz (models with option SA6 only)	< -158 dBm/Hz (< -161 dBm/Hz, typical)
4 GHz - 6 GHz (models with option SA6 only)	< -150 dBm/Hz (< -155 dBm/Hz, typical)

Spurious response

2^nd and 3^rd harmonic distortion (>100 MHz)

< -60 dBc (< -60 dBc, typical), with auto settings on and signals 10 dB below reference level

2^nd and 3^rd harmonic distortion (9 kHz to 100 MHz )

< -57 dBc (< -65 dBc, typical), with auto settings on, signals 10 dB below reference level, and reference level ≤ -15 dBm

2^nd order intermodulation distortion (>200 MHz)

< -60 dBc (< -65 dBc, typical), with auto settings on and signals 10 dB below reference level

2^nd order intermodulation distortion (>100 MHz to ≤200 MHz)

<-57 dBc (<-60 DBc, typical), with auto settings on and signals 10 dB below reference level

2^nd order intermodulation distortion (10 MHz to 100 MHz)

< -60 dBc (< -65 dBc, typical), with auto settings on, signals 10 dB below reference level, and reference level ≤ -15 dBm

3^rd order intermodulation distortion (>10 MHz)

< -62 dBc (<-65 dBc, typical), with auto settings on and signals 10 dB below reference level, and reference levels < -15 dBm

3^rd order intermodulation distortion (9 kHz to 10 MHz)

< -62 dBc (<-65 dBc, typical), with auto settings on and signals 10 dB below reference level, and reference levels < -15 dBm

A/D spurs

< -60 dBc (< -65 dBc, typical), with auto settings on and signals 5 dB below reference level. Excludes A/D aliasing spurs

A/D aliasing spurs

At (5 GHz - F_in) and (8 GHz - F_in): <-55 dBc (<-60 dBc, typical), with auto settings on and signals 5 dB below reference level

Specifications that only apply to models with option SA6

IF Rejection: (All Input Frequencies except: 1.00 GHz to 1.25 GHz and 2 GHz to 2.4 GHz): < -55 dBc, typical

IF spurs at (5 GHz - F_in ) for input frequencies from 1.00 GHz to 1.25 GHz: < -50 dBc, typical

IF spurs at (6.5 GHz -F_in ) for input frequencies from 2 GHz to 2.4 GHz: < -50 dBc, typical

Image Rejection: < -50 dBc (for input frequencies from 5.5 GHz to 9.5 GHz)

Residual response

< -85 dBm (< -78 dBm at 3.75 GHz, 4.0 GHz, 5.0 GHz, and typical 6.0 GHz; < -73 dBm at 2.5 GHz) with ≤ -25 dBm reference level and input terminated with 50 Ω

Absolute amplitude accuracy

Accuracy of power level measurements at the center frequency. At frequencies away from center frequency, add Channel Response to the Absolute Amplitude Accuracy. Applies to signal to noise ratios > 40 dB.

< ± 1.0 dB (< ±0.5 dB, typical), 18 °C - 28 °C temperature range, 50 kHz to 6 GHz frequency range, reference levels -25, -20, -15, -10, -5, 0, 5, 10 dBm

< ± 1.0 dB, typical, 50 kHz to 6 GHz, all other reference levels, 18 °C - 28 °C temperature range

< ±1.5 dB, typical, 50 kHz to 6 GHz, all reference levels, 0 ⁰C to 50 ⁰C temperature range

< ± 2.0 dB, typical, 9 kHz to 50 kHz, all reference levels, 18 °C to 28 °C temperature range

< ± 3.0 dB, typical, 9 kHz to 50 kHz, all reference levels, 0 °C to 50 °C temperature range

Channel response

Valid over 18 - 28 °C temperature range

Specification applies to signal-to-noise ratios > 40 dB

Measurement center frequency range	Span	Amplitude flatness, pk-pk (typical)	Amplitude flatness, RMS (typical)	Phase linearity, RMS (typical)
15 MHz - 6 GHz	10 MHz	0.3 dB	0.15 dB	1.5 °
60 MHz - 6 GHz	≤ 100 MHz	0.75 dB	0.27 dB	1.5 °
170 MHz - 6 GHz	≤ 320 MHz	0.85 dB	0.27 dB	2.5 °
510 MHz - 6 GHz	≤ 1,000 MHz	1.0 dB	0.3 dB	3.0 °
Any, (for start frequency > 10 MHz)	> 1,000 MHz	1.2 dB	N/A	N/A

Absolute amplitude accuracy (AAA) and channel response (CR), with TPA-N-PRE preamp attached

AAA: ≤ ±0.5 dB (typical), 18 ⁰C - 28 ⁰C temperature range, 50 kHz to 6 GHz, either preamp state.

AAA: ≤ ±2.0 dB (typical), 18 ⁰C - 28 ⁰C temperature range, 9 kHz to 50 kHz, either preamp state.

AAA: ≤ ±2.3 dB (typical), over full operating range, either preamp state.

CR: 0.0 dB

Crosstalk to spectrum analyzer from oscilloscope channels

≤1 GHz input frequencies

< -68 dB from ref level

>1 GHz - 2 GHz input frequencies

< -48 dB from ref level

Phase noise at 1 GHz CW

1 kHz

< -104 dBc/Hz,(typical)

10 kHz

< -108 dBc/Hz, < -111 dBc/Hz (typical)

100 kHz

< -110 dBc/Hz, < -113 dBc/Hz (typical)

1 MHz

< -120 dBc/Hz, < -123 dBc/Hz (typical)

Reference frequency error (cumulative)

Cumulative error: 1.6 x 10^-6

Includes allowances for aging per year, reference frequency calibration accuracy, and temperature stability

Valid over the recommended one-year calibration interval, from 0 °C to +50 °C

Marker frequency measurement accuracy

±((1.6x 10^-6 x Marker-Frequency) + (0.001 x span + 2)) Hz

Example: assuming the span is set to 10 kHz and the marker is at 1500 MHz, this would result in a Frequency Measurement Accuracy of +/-((1.6 x 10 -6 x 1500 MHz) + (0.001 x 10 kHz + 2)) = +/- 2.412 kHz.

Marker Frequency with Span/RBW ≤ 1000:1

Reference Frequency Error with Marker level to displayed noise level > 30 dB

Frequency measurement resoultion

1 Hz

Maximum operating input level

Average continuous power

+30 dBm (1 W) for reference levels ≥ -20 dBm

+24 dBm (0.25 W) for reference levels < -20 dBm

DC maximum before damage

±40 V_DC

Maximum power before damage (CW)

+32 dBm (1.6 W) for reference levels ≥ -20 dBm

+25 dBm (0.32 W) for reference levels of < -20 dBm

Maximum power before damage (pulse)

Peak Pulse Power: +45 dBm (32 W)

Peak Pulse Power defined as <10 μs pulse width, <1% duty cycle, and reference level of ≥ +10 dBm

Maximum operating input level with TPA-N-PRE preamp attached

Average continuous power

+30 dBm (1 W)

DC maximum before damage

±20 V_DC

Maximum power before damage (CW)

+30 dBm (1 W)

Maximum power before damage (pulse)

+45 dBm (32 W) (<10 μs pulse width, <1% duty cycle, and reference level of ≥ +10 dBm)

RF Power level trigger

Frequency range

Models with option SA3: 1 MHz to 3 GHz

Models with option SA6: 1 MHz to 3.75 GHz; 2.75 GHz to 4.5 GHz, 3.5 GHz to 6.0 GHz

Amplitude operating level

0 dB to -30 dB from Reference Level

Amplitude range

+10 dB to -40 dB from Reference Level and within the range of -65 dBm to +30 dBm

Minumum pulse generation

10 µs On Time with a minimum settling Off Time of 10 µs

Spectrum analyzer to analog channel skew

<5 ns

RF acquisition length

Span	Maximum RF acquisition time
>2 GHz	5 ms
>1 GHz - 2 GHz	10 ms
>800 MHz - 1 GHz	20 ms
>500 MHz - 800 MHz	25 ms
>400 MHz - 500 MHz	40 ms
>250 MHz - 400 MHz	50 ms
>200 MHz - 250 MHz	80 ms
>160 MHz - 200 MHz	100 ms
>125 MHz - 160 MHz	125 ms
<125 MHz	158 ms

FFT window types, factors, and RBW accuracy

FFT window	Factor	RBW accuracy
Kaiser	2.23	0.90%
Rectangular	0.89	2.25%
Hamming	1.30	1.54%
Hanning	1.44	1.39%
Blackman-Harris	1.90	1.05%
Flat-Top	3.77	0.53%

Waveforms

Sine, Square, Pulse, Ramp/Triangle, DC, Noise, Sin(x)/x (Sinc), Gaussian, Lorentz, Exponential Rise, Exponential Decay, Haversine, Cardiac, and Arbitrary.

Sine

Frequency range

0.1 Hz to 50 MHz

Amplitude range

20 mV_p-p to 5 V_p-p into Hi-Z; 10 mV_p-p to 2.5 V_p-p into 50 Ω

Amplitude flatness (typical)

±0.5 dB at 1 kHz (±1.5 dB for <20 mV_p-p amplitudes)

Total harmonic distortion (typical)

1% into 50 Ω

2% for amplitude < 50 mV and frequencies > 10 MHz

3% for amplitude < 20 mV and frequencies > 10 MHz

Spurious free dynamic range (SFDR) (typical)

-40 dBc (V_p-p ≥ 0.1 V); -30dBc (V_p-p ≤ 0.1 V), 50 Ω load

Square / Pulse

Frequency range

0.1 Hz to 25 MHz

Amplitude range

20 mV_p-p to 5 V_p-p into Hi-Z; 10 mV_p-p to 2.5 V_p-p into 50 Ω

Duty cycle

10% to 90% or 10 ns minimum pulse, whichever is larger cycle

Duty cycle resolution

0.1%

Pulse width minimum (typical)

10 ns

Rise/fall time (typical)

5 ns (10% - 90%)

Pulse width resolution

100 ps

Overshoot (typical)

< 2% for signal steps greater than 100 mV

Asymmetry

±1% ±5 ns, at 50% duty cycle

Jitter (TIE RMS) (typical)

< 500 ps

Ramp / Triangle

Frequency range

0.1 Hz to 500 kHz

Amplitude range

20 mV_p-p to 5 V_p-p into Hi-Z; 10 mV_p-p to 2.5 V_p-p into 50 Ω

Variable symmetry

0% to 100%

Symmetry resolution

0.1%

DC

Level range (typical)

±2.5 V into Hi-Z; ±1.25 V into 50 Ω

Noise

Amplitude range

20 mV_p-p to 5 V_p-p in to Hi-Z; 10 mV_p-p to 2.5 V_p-p into 50 Ω

Amplitude resolution

0% to 100% in 1% increments

Sin(x)/x (Sinc)

Frequency range (typical)

0.1 Hz to 2 MHz

Amplitude range

20 mV_p-p to 3.0 V_p-p into Hi-Z; 10 mV_p-p to 1.5 V_p-p into 50 Ω

Gaussian

Frequency range (typical)

0.1 Hz to 5 MHz

Amplitude range

20 mV_p-p to 2.5 V_p-p into Hi-Z; 10 mV_p-p to 1.25 V_p-p into 50 Ω

Lorentz

Frequency range (typical)

0.1 Hz to 5 MHz

Amplitude range

20 mV_p-p to 2.4 V_p-p into Hi-Z; 10 mV_p-p to 1.2 V_p-p into 50 Ω

Exponential Rise / Decay

Frequency range (typical)

0.1 Hz to 5 MHz

Amplitude range

20 mV_p-p to 2.5 V_p-p into Hi-Z; 10 mV_p-p to 1.25 V_p-p into 50 Ω

Haversine

Frequency range (typical)

0.1 Hz to 5 MHz

Amplitude range

20 mV_p-p to 2.5 V_p-p into Hi-Z; 10 mV_p-p to 1.25 V_p-p into 50 Ω

Cardiac (typical)

Frequency range

0.1 Hz to 500 kHz

Amplitude range

20 mV_p-p to 5 V_p-p into Hi-Z; 10 mV_p-p to 2.5 V_p-p into 50 Ω

Arbitrary

Memory depth

1 to 128 k

Amplitude range

20 mV_p-p to 5 V_p-p into Hi-Z; 10 mV_p-p to 2.5 V_p-p into 50 Ω

Repetition rate

0.1 Hz to 25 MHz

Sample rate

250 MS/s

Frequency accuracy

Sine wave and ramp

130 ppm (frequency < 10 kHz)

50 ppm (frequency ≥ 10 kHz)

Square wave and pulse

130 ppm (frequency < 10 kHz)

50 ppm (frequency ≥ 10 kHz)

Resolution

0.1 Hz or 4 digits, whichever is larger

Amplitude accuracy

±[ (1.5% of peak-to-peak amplitude setting) + (1.5% of DC offset setting) + 1 mV ] (frequency = 1 kHz)

DC offset

DC offset range

±2.5 V into Hi-Z; ±1.25 V into 50 Ω

DC offset resolution

1 mV into Hi-Z; 500 uV into 50 Ω

Offset accuracy

±[(1.5% of absolute offset voltage setting) + 1 mV]; derated 3 mV for every 10 °C away from 25 °C

ArbExpress®

The MDO4000C is compatible with ArbExpress ® PC-based signal generator waveform creation and editing software. Capture waveforms on the MDO4000C oscilloscope and transfer them to ArbExpress for editing. Create complex waveforms in ArbExpress and transfer them to the arbitrary function generator in the MDO4000C for output. To download ArbExpress software, go to

www.tek.com/software/downloads.

Input channels

16 digital (D15 to D0)

Thresholds

Threshold per channel

Threshold selections

TTL, CMOS, ECL, PECL, User-defined

User-defined threshold range

±40 V

Threshold accuracy

±[100 mV + 3% of threshold setting]

Maximum input voltage

±42 V_peak (typical)

Input dynamic range

30 V_p-p ≤200 MHz

10 V_p-p >200 MHz

Minimum voltage swing

400 mV_p-p

Probe loading

Input impedance

100 kΩ

Input capacitance

3 pF

Vertical resolution

1 bit

Maximum sample rate (Main)

500 MS/s (2 ns resolution)

Maximum record length (Main)

20 M

Maximum sample rate (MagniVu)

16.5 GS/s (60.6 ps resolution)

Maximum record length (MagniVu)

10k centered on the trigger

Minimum detectable pulse width

1 ns

Channel-to-channel skew (typical)

200 ps (typical)

Maximum input toggle rate

500 MHz (Maximum frequency sine wave that can accurately be reproduced as a logic square wave. Requires the use of a short ground extender on each channel. This is the maximum frequency at the minimum swing amplitude. Higher toggle rates can be achieved with higher amplitudes.)

Trigger types

I²C

Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data on I²C buses up to 10 Mb/s.

SPI

Trigger on SS active, Start of Frame, MOSI, MISO, or MOSI and MISO on SPI buses up to 50.0 Mb/s.

RS-232/422/485/UART

Trigger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx End of Packet, Tx Data, Rx Data, Tx Parity Error, and Rx Parity Error up to 10 Mb/s.

USB: Low speed

Trigger on Sync Active, Start of Frame, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error.

Token packet trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range. Frame number can be specified for SOF token using binary, hex, unsigned decimal and don't care digits.

Data packet trigger - Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range.

Handshake packet trigger - Any handshake type, ACK, NAK, STALL.

Special packet trigger - Any special type, Reserved

Error trigger - PID Check, CRC5 or CRC16, Bit Stuffing.

USB: Full speed

Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error.

Token packet trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range. Frame number can be specified for SOF token using binary, hex, unsigned decimal and don't care digits.

Data packet trigger - Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range.

Handshake packet trigger - Any handshake type, ACK, NAK, STALL.

Special packet trigger - Any special type, PRE, Reserved.

Error trigger - PID Check, CRC5 or CRC16, Bit Stuffing.

USB: High speed²

Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error.

Token packet trigger - Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range. Frame number can be specified for SOF token using binary, hex, unsigned decimal and don't care digits.

Data packet trigger - Any data type, DATA0, DATA1, DATA2, MDATA; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range.

Handshake packet trigger - Any handshake type, ACK, NAK, STALL, NYET.

Special packet trigger - Any special type, ERR, SPLIT, PING, Reserved. SPLIT packet components that can be specified include:

Hub Address

Start/Complete - Don't Care, Start (SSPLIT), Complete (CSPLIT)

Port Address

Start and End bits - Don't Care, Control/Bulk/Interrupt (Full-speed Device, Low-speed Device), Isochronous (Data is Middle, Data is End, Data is Start, Data is All)

Endpoint Type - Don't Care, Control, Isochronous, Bulk, Interrupt

Error trigger - PID Check, CRC5 or CRC16

Ethernet ³

10BASE-T and 100BASE-TX: Trigger on Start Frame Delimiter, MAC Addresses, MAC Q-Tag Control Information, MAC Length/Type, IP Header, TCP Header, TCP/IPv4/MAC Client Data, End of Packet, and FCS (CRC) Error.

100BASE-TX: Idle.

MAC Addresses - Trigger on Source and Destination 48-bit address values.

MAC Q-Tag Control Information - Trigger on Q-Tag 32-bit value.

MAC Length/Type - Trigger on ≤, <, =, >, ≥, ≠ a particular 16-bit value, or inside or outside of a range.

IP Header - Trigger on IP Protocol 8-bit value, Source Address, Destination Address.

TCP Header - Trigger on Source Port, Destination Port, Sequence Number, and Ack Number.

TCP/IPv4/MAC Client Data - Trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range. Selectable number of bytes to trigger on from 1-16. Byte offset options of Don't Care, 0-1499.

CAN, CAN FD (ISO and non-ISO)

Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data, End of Frame, Missing ACK, or Bit Stuffing Error on CAN signals up to 1 Mb/s and on CAN FD signals up to 10 Mb/s. Data can be further specified to trigger on ≤, <, =, >, ≥, or ≠ a specific data value. User-adjustable sample point is set to 50% by default.

LIN

Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup Frame, Sleep Frame, Errors such as Sync, Parity, or Checksum Errors up to 100 kb/s (by LIN definition, 20 kb/s).

FlexRay

Trigger on Start of Frame, Type of Frame (Normal, Payload, Null, Sync, Startup), Identifier, Cycle Count, Complete Header Field, Data, Identifier and Data, End of Frame or Errors such as Header CRC, Trailer CRC, Null Frame, Sync Frame, or Startup Frame Errors up to 100 Mb/s.

MIL-STD-1553 

Trigger on Sync, Word Type³ (Command, Status, Data), Command Word (set RT Address, T/R, Sub-address/Mode, Data Word Count/Mode Code, and Parity individually), Status Word (set RT Address, Message Error, Instrumentation, Service Request Bit, Broadcast Command Received, Busy, Subsystem Flag, Dynamic Bus Control Acceptance (DBCA), Terminal Flag, and Parity individually), Data Word (user-specified 16-bit data value), Error (Sync, Parity, Manchester, Non-contiguous data), Idle Time (minimum time selectable from 2 µs to 100 µs; maximum time selectable from 2 µs to 100 µs; trigger on < minimum, > maximum, inside range, outside range). RT Address can be further specified to trigger on =, ≠, <, >, ≤, ≥ a particular value, or inside or outside of a range.

ARINC-429

Trigger on Word Start/End, Label, SDI, Data, Label and Data, Error conditions (any, parity, word, gap)

I²S/LJ/RJ/TDM

Trigger on Word Select, Frame Sync, or Data. Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a specific data value, or inside or outside of a range. Maximum data rate for I²S/LJ/RJ is 12.5 Mb/s. Maximum data rate for TDM is 25 Mb/s.

Source

Channel 1, Channel 2, Channel 3, Channel 4 

Measurement types

AC RMS, DC, AC+DC RMS (reads out in volts or amps); Frequency

Voltage accuracy

±(1.5% |reading - offset - position|) + (0.5% |(offset - position)|) + (0.1 * Volts/div))

Resolution

ACV, DCV: 4 digits

Frequency: 5 digits

Frequency accuracy

±(10 µHz/Hz + 1 count)

Measuring rate

100 times/second; measurements updated on the display 4 times/second

Vertical settings autorange

Automatic adjustment of vertical settings to maximize measurement dynamic range; available for any non-trigger source

Graphical measurement

Graphical indication of minimum, maximum, current value, and five second rolling range

Display type

10.4 in. (264 mm) liquid-crystal TFT color display

Display resolution

1,024 horizontal × 768 vertical pixels (XGA)

Interpolation

Sin(x)/x

Waveform styles

Vectors, Dots, Variable Persistence, Infinite Persistence

Graticules

Full, Grid, Solid, Cross Hair, Frame, IRE and mV

Format

YT, XY, and simultaneous XY/YT

Maximum waveform capture rate

>340,000 wfms/s in FastAcq acquisition mode on 1 GHz models

>270,000 wfms/s in FastAcq acquisition mode on 200 MHz - 500 MHz models

>50,000 wfms/s in DPO acquisition mode on all models.

USB 2.0 high-speed host port

Supports USB mass storage devices and keyboard. Two ports on front and two ports on rear of instrument.

USB 2.0 device port

Rear-panel connector allows for communication/control of oscilloscope through USBTMC or GPIB (with a TEK-USB-488), and direct printing to all PictBridge-compatible printers.

Printing

Print PictBridge printer or to a printer that supports e-mail printing. Note: This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)

LAN port

RJ-45 connector, supports 10/100/1000 Mb/s

Video out port

DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector. XGA resolution.

Probe compenstor output voltage and frequency

Front-panel pins

Amplitude

0 to 2.5 V

Frequency

1 kHz

Auxiliary out

Rear-panel BNC connector

V_OUT (Hi): ≥2.5 V open circuit, ≥1.0 V 50 Ω to ground

V_OUT (Lo): ≤0.7 V into a load of ≤4 mA; ≤0.25 V 50 Ω to ground

Output can be configured to provide a pulse out signal when the oscilloscope triggers, the internal oscilloscope reference clock out, or an event out for limit/mask testing.

External reference input

Time-base system can phase lock to an external 10 MHz reference (10 MHz ±1%)

Kensington-style lock

Rear-panel security slot connects to standard Kensington-style lock.

VESA mount

Standard (MIS-D 100) 100 mm VESA mounting points on rear of instrument.

Class

LXI Core 2011 

Version

V1.4 

OpenChoice® Desktop

Enables fast and easy communication between a Windows PC and your oscilloscope using USB or LAN. Transfer and save settings, waveforms, measurements, and screen images. Included Word and Excel toolbars automate the transfer of acquisition data and screen images from the oscilloscope into Word and Excel for quick reporting or further analysis. Download from www.tek.com/software/downloads.

IVI driver

Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI, MicrosoftNET, and MATLAB.

e*Scope® Web-based interface

Enables control of the oscilloscope over a network connection through a standard web browser. Simply enter the IP address or network name of the oscilloscope and a web page will be served to the browser. Transfer and save settings, waveforms, measurements, and screen images or make live control changes to settings on the oscilloscope directly from the web browser.

LXI Web interface

Connect to the oscilloscope through a standard Web browser by simply entering the oscilloscope's IP address or network name in the address bar of the browser. The Web interface enables viewing of instrument status and configuration, status and modification of network settings, and instrument control through the e*Scope Web-based remote control. All Web interaction conforms to LXI Core specification, version 1.4.

Power source voltage

100 to 240 V ±10%

Power source frequency

50 to 60 Hz ±10% at 100 to 240 V ±10%

400 Hz ±10% at 115 V ±13%

Power consumption

250 W maximum

Dimensions

	mm	in
Height	229	9
Width	439	17.3
Depth	147	5.8

Weight

Instruments without option SA3 or SA6

	kg	lb
Net	5.1	11.2
Shipping	10.8	23.8

Instruments with option SA3 or SA6

	kg	lb
Net	5.5	12.2
Shipping	11.2	24.8

Rackmount configuration

5U

Cooling clearance

2 in. (51 mm) required on left side and rear of instrument

Temperature

Operating

0 ºC to +50 ºC (+32 ºF to +122 ºF)

Nonoperating

-30 ºC to +70 ºC (-22 ºF to +158 ºF)

Humidity

Operating

High: 40 ºC to 50 ºC, 10% to 60% relative humidity, Low: 0 ºC to 40 ºC, 10% to 90% relative humidity

Nonoperating

High: 40 ºC to 60 ºC, 5% to 55% relative humidity, Low: 0 ºC to 40 ºC, 5% to 90% relative humidity

Altitude

Operating

3,000 meters (9,843 feet)

Nonoperating

12,000 meters (39,370 feet)

Regulatory

CE marked for the European Union and UL approved for the US and Canada

MDO4024C

Mixed Domain Oscilloscope with (4) 200 MHz analog channels

MDO4034C

Mixed Domain Oscilloscope with (4) 350 MHz analog channels

MDO4054C

Mixed Domain Oscilloscope with (4) 500 MHz analog channels

MDO4104C

Mixed Domain Oscilloscope with (4) 1 GHz analog channels

≤ 500 MHz models

TPP0500B, 500 MHz bandwidth, 10X, 3.9 pF. One passive voltage probe per analog channel.

1 GHz models

TPP1000, 1 GHz bandwidth, 10X, 3.9 pF. One passive voltage probe per analog channel.

Any model with MDO4MSO option

One P6616 16-channel logic probe and a logic probe accessory kit (020-2662-xx).

200-5130-xx

Front cover

016-2030-xx

Accessory bag

071-3448-xx

Installation and Safety Instructions, printed manual (translated in English, French, Japanese, and Simplified Chinese); other product manuals are available for download at www.tek.com/manual/downloads

-

Power cord

-

OpenChoice® Desktop Software (available on the Documentation CD and for download from www.tek.com/software/downloads.)

-

Calibration certificate documenting traceability to National Metrology Institute(s) and ISO9001 quality system registration

103-0045-xx models with option SA3 or SA6 

N-to-BNC adapter

All MDO4000C Series instruments can be preconfigured from the factory with the following options:

MDO4AFG

Arbitrary function generator with 13 predefined waveforms and arbitrary waveform generation

MDO4MSO

16 digital channels; includes P6616 digital probe and accessories

SA3

Integrated spectrum analyzer with frequency range of 9 kHz to 3 GHz

SA6

Integrated spectrum analyzer with frequency range of 9 kHz to 6 GHz

MDO4SEC

Enhanced instrument security to enable password protected control of turning on/off all instrument ports and instrument firmware update functionality

Opt. A0

North America power plug (115 V, 60 Hz)

Opt. A1

Universal Euro power plug (220 V, 50 Hz)

Opt. A2

United Kingdom power plug (240 V, 50 Hz)

Opt. A3

Australia power plug (240 V, 50 Hz)

Opt. A5

Switzerland power plug (220 V, 50 Hz)

Opt. A6

Japan power plug (100 V, 50/60 Hz)

Opt. A10

China power plug (50 Hz)

Opt. A11

India power plug (50 Hz)

Opt. A12

Brazil power plug (60 Hz)

Opt. A99

No power cord

All products are shipped with an Installation and Safety manual that is in English, Japanese, Simplified Chinese, and French. Full user manuals translated in each language listed below are available in PDF format from www.tek.com/manual/downloads. Selecting a language option below other than L0 will include a front panel overlay in the language selected.

Opt. L0

English front panel label

Opt. L1

French front panel overlay

Opt. L2

Italian front panel overlay

Opt. L3

German front panel overlay

Opt. L4

Spanish front panel overlay

Opt. L5

Japanese front panel overlay

Opt. L6

Portuguese front panel overlay

Opt. L7

Simplified Chinese front panel overlay

Opt. L8

Traditional Chinese front panel overlay

Opt. L9

Korean front panel overlay

Opt. L10

Russian front panel overlay

Tektronix offers a range of warranty and service plans to extend the life of your product and protect you from unplanned costs. Whether you want to protect yourself from accidental damage, or just save money on maintenance with a calibration plan, there is a service option available that meets your needs.

Opt. T3

Three year total protection plan ensures that your equipment remains like-new regardless of what happens.

Opt. T5

Five year total protection plan ensures that your equipment remains like-new regardless of what happens.

Probes and accessories are not covered by the oscilloscope warranty and service offerings. Refer to the datasheet of each probe and accessory model for its unique warranty and calibration terms.

Application modules

Application modules are purchased as stand-alone products and can be purchased at the time of initial MDO4000C purchase or at any future time. The optional application modules functionality is offered free for a 30-day trial period. This free trial period starts automatically when the instrument is powered on for the first time.

Application modules have licenses which can be transferred between an application module and an oscilloscope. The license may be contained in the module; allowing the module to be moved from one instrument to another. Or, the license can be contained in the oscilloscope; allowing the module to be removed and stored for safekeeping. Transferring the license to an oscilloscope and removing the module permits the use of more than 4 applications simultaneously.

DPO4BND

Application bundle module that enables all of the functionality of the DPO4AERO, DPO4AUDIO, DPO4AUTO, DPO4COMP, DPO4EMBD, DPO4ENET, DPO4LMT, DPO4PWR, DPO4USB and DPO4VID application modules in a single module. Save money when multiple serial bus debug and analysis application modules are required and easily move the entire set of functionality from one instrument to another.

DPO4AERO

Aerospace Serial Triggering and Analysis Module. Enables triggering on packet-level information on MIL-STD-1553 and ARINC-429 buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information.

Signal Inputs - Any Ch1 - Ch4, Math, Ref1 - Ref4

Recommended Probing - Differential or single ended (only one single-ended signal required)

DPO4AUDIO

Audio Serial Triggering and Analysis Module. Enables triggering on packet-level information on I²S, LJ, RJ, and TDM audio buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information.

Signal Inputs - Any Ch1 - Ch4, any D0 - D15

Recommended Probing - Single ended

DPO4AUTO

Automotive Serial Triggering and Analysis Module. Enables triggering on packet-level information on CAN, CAN FD (ISO and non-ISO), and LIN buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time- stamp information.

Signal Inputs – LIN: Any Ch1 - Ch4, any D0 - D15; CAN, CAN FD: Any Ch1 - Ch4, any D0 - D15

Recommended Probing – LIN: Single ended; CAN, CAN FD: Single ended or differential

DPO4AUTOMAX

Includes DPO4AUTO functionality and adds FlexRay trigger, decode, search and decode tables support. Extended eye diagram analysis is also supported with a PC-based software package.

DPO4COMP

Computer Serial Triggering and Analysis Module. Enables triggering on packet-level information on RS-232/422/485/UART buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information.

Signal Inputs - Any Ch1 - Ch4, any D0 - D15

Recommended Probing - RS-232/UART: Single ended; RS-422/485: Differential

DPO4EMBD

Embedded Serial Triggering and Analysis Module. Enables triggering on packet-level information on I2C and SPI buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time- stamp information.

Signal Inputs - I²C or SPI: Any Ch1 - Ch4, any D0 - D15

Recommended Probing - Single ended

DPO4ENET

Ethernet Serial Triggering and Analysis Module. Enables triggering on packet-level information on 10BASE-T and 100BASE-TX ⁴ buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information.

Signal Inputs - Any Ch1 - Ch4, Math, Ref1 - Ref4

Recommended Probing - 10BASE-T: Single ended or differential; 100BASE-TX: Differential

DPO4USB

USB Serial Triggering and Analysis Module. Enables triggering on packet-level content for low-speed, and full-speed USB serial buses. Also enables analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information for low-speed, full-speed, and high-speed USB serial buses. ⁵

Signal Inputs - Low-speed and Full-speed: Any Ch1 - Ch4, any D0 - D15; Low-speed, Full-speed, and High-speed: Any Ch1 - Ch4, Math, Ref1 - Ref4

Recommended Probing - Low-speed and Full-speed: Single ended or differential; High-speed: Differential

DPO4PWR

Power Analysis Application Module. Enables quick and accurate analysis of power quality, switching loss, harmonics, safe operating area (SOA), modulation, ripple, and slew rate (dI/dt, dV/dt).

DPO4LMT

Limit and Mask Testing Application Module. Enables testing against limit templates generated from "golden" waveforms and mask testing using custom masks. ⁶

DPO4VID

HDTV and Custom (nonstandard) Video Triggering and Video Picture Module.

MDO4TRIG

Advanced RF Power Level Triggering Module. Enables the power level on the spectrum analyzer input to be used as a source in the following trigger types: Pulse Width, Runt, Timeout, Logic, and Sequence.

Tektronix offers over 100 different probes to meet your application needs. For a comprehensive listing of available probes, please visit www.tek.com/probes.

TPP0500B

500 MHz, 10X TekVPI® passive voltage probe with 3.9 pF input capacitance

TPP0502

500 MHz, 2X TekVPI® passive voltage probe with 12.7 pF input capacitance

TPP0850

2.5 kV, 800 MHz, 50X TekVPI® passive high-voltage probe

TPP1000

1 GHz, 10X TekVPI® passive voltage probe with 3.9 pF input capacitance

TAP1500

1.5 GHz TekVPI® active single-ended voltage probe

TAP2500

2.5 GHz TekVPI® active single-ended voltage probe

TAP3500

3.5 GHz TekVPI® active single-ended voltage probe

TCP0030

120 MHz TekVPI® 30 Ampere AC/DC current probe

TCP0150

20 MHz TekVPI® 150 Ampere AC/DC current probe

TDP0500

500 MHz TekVPI® differential voltage probe with ±42 V differential input voltage

TDP1000

1 GHz TekVPI® differential voltage probe with ±42 V differential input voltage

TDP1500

1.5 GHz TekVPI® differential voltage probe with ±8.5 V differential input voltage

TDP3500

3.5 GHz TekVPI® differential voltage probe with ±2 V differential input voltage

THDP0200

±1.5 kV, 200 MHz TekVPI® high-voltage differential probe

THDP0100

±6 kV, 100 MHz TekVPI® high-voltage differential probe

TMDP0200

±750 V, 200 MHz TekVPI® high-voltage differential probe

P5100A

2.5 kV, 500 MHz, 100X high-voltage passive probe

P5200A

1.3 kV, 50 MHz high-voltage differential probe

TPA-N-PRE

Preamplifier, 12 dB nominal Gain, 9 kHz - 6 GHz

119-4146-00 

Near field probe set, 100 kHz - 1 GHz

119-6609-00 

Flexible monopole antenna

TPA-N-VPI

N-to-TekVPI adapter

077-0585-xx

Service manual (English only)

TPA-BNC

TekVPI® to TekProbe™ BNC adapter

TEK-DPG

TekVPI Deskew pulse generator signal source

067-1686-xx

Power measurement deskew and calibration fixture

SignalVu-PC-SVE

Vector Signal Analysis Software

TEK-USB-488 

GPIB-to-USB adapter

ACD4000B

Soft transit case

HCTEK54

Hard transit case (requires ACD4000B)

RMD5000

Rackmount kit

Contact Beehive Electronics to order: http://beehive-electronics.com/probes.html

101A

EMC probe set

150A

EMC probe amplifier

110A

Probe cable

0309-0001 

SMA probe adapter

0309-0006 

BNC probe adapter

Free instrument options

The following options are available free of charge when the MDO4000C product is registered at www.tek.com/mdo4register.

Digital Voltmeter and Frequency Counter

4-digit AC_rms, DC, AC+DC_rms voltage measurements and 5-digit frequency counter. Unique software option key provided upon instrument registration enables the features.

Post-purchase instrument options

The following products are sold as stand-alone products and can be purchased at any time to add functionality to any MDO4000C product.

MDO4AFG

Add arbitrary function generator to any MDO4000C Series product.

One-time, permanent upgrade to any model enabled through single-use application module hardware key. The hardware key is used to enable the feature and then is not required for future use.

MDO4MSO

Add 16 digital channels; includes P6616 digital probe and accessories .

One-time, permanent upgrade to any model enabled through single-use application module hardware key. The hardware key is used to enable the feature and then is not required for future use.

MDO4SA3

Add integrated spectrum analyzer with input frequency range of 9 kHz – 3 GHz .

One-time, permanent upgrade to any model. This upgrade requires installation at a Tektronix service center and requires an instrument calibration.

MDO4SA6

Add integrated spectrum analyzer with input frequency range of 9 kHz – 6 GHz.

One-time, permanent upgrade to any model. This upgrade requires installation at a Tektronix service center and requires an instrument calibration.

MDO4SEC

Add enhanced instrument security to enable password protected control of turning on/off all instrument ports and instrument firmware update functionality.

One-time, permanent upgrade to any model enabled through software option key. Software option key products require that the instrument model and serial number be provided at the time of purchase. The software option key is specific to the model and serial number combination.

Spectrum analyzer upgrade options

The spectrum analyzer maximum input frequency range can be upgraded from 3 GHz to 6 GHz. This upgrade requires installation at a Tektronix service center and requires an instrument calibration. (Spectrum analyzer upgrades and instrument calibrations will appear as separate order line items. An optional incoming calibration is available upon request.)

MDO4SA3T6

3 GHz to 6 GHz spectrum analyzer upgrade for MDO4000C.

Post-purchase service products

The following upgrades can be added to any model to extend the product warranty beyond the standard warranty period.

MDO4024C-R5DW

Repair service coverage 5 years for a MDO4024C product (includes product warranty period).

MDO4034C-R5DW

Repair service coverage 5 years for a MDO4034C product (includes product warranty period).

MDO4054C-R5DW

Repair service coverage 5 years for a MDO4054C product (includes product warranty period).

MDO4104C-R5DW

Repair service coverage 5 years for a MDO4104C product (includes product warranty period).

MDO4000CT3

Three year total protection plan ensures that your equipment remains like-new regardless of what happens. Available for 30-days after the initial purchase of the instrument.

MDO4000CT5

Five year total protection plan ensures that your equipment remains like-new regardless of what happens. Available for 30-days after the initial purchase of the instrument.

Bandwidth upgrade options

Instrument bandwidth can be upgraded on any MDO4000C Series product after initial purchase. Each upgrade product increases the analog bandwidth of the oscilloscope. Bandwidth upgrades are purchased based on the combination of the current bandwidth and the desired bandwidth and whether the current instrument contains an integrated spectrum analyzer. Bandwidth upgrade products include new analog probes if applicable. All analog bandwidth upgrades require installation at a Tektronix service center and an instrument calibration. (Bandwidth upgrades and instrument calibrations will appear as separate order line items. An optional incoming calibration is available upon request.)

Model to be upgraded	Instrument has option SA3 or SA6 (spectrum analyzer)	Bandwidth before upgrade	Bandwidth after upgrade	Order product
MDO4024C	No	200 MHz	350 MHz	MDO4BW2T34
		200 MHz	500 MHz	MDO4BW2T54
		200 MHz	1 GHz	MDO4BW2T104
		350 MHz	500 MHz	MDO4BW3T54
		350 MHz	1 GHz	MDO4BW3T104
		500 MHz	1 GHz	MDO4BW5T104
MDO4034C	No	350 MHz	500 MHz	MDO4BW3T54
		350 MHz	1 GHz	MDO4BW3T104
		500 MHz	1 GHz	MDO4BW5T104
MDO4054C	No	500 MHz	1 GHz	MDO4BW5T104
MDO4024C	Yes	200 MHz	350 MHz	MDO4BW2T34-SA
		200 MHz	500 MHz	MDO4BW2T54-SA
		200 MHz	1 GHz	MDO4BW2T104-SA
		350 MHz	500 MHz	MDO4BW3T54-SA
		350 MHz	1 GHz	MDO4BW3T104-SA
		500 MHz	1 GHz	MDO4BW5T104-SA
MDO4034C	Yes	350 MHz	500 MHz	MDO4BW3T54-SA
		350 MHz	1 GHz	MDO4BW3T104-SA
		500 MHz	1 GHz	MDO4BW5T104-SA
MDO4054C	Yes	500 MHz	1 GHz	MDO4BW5T104-SA