Contact us
Live Chat with Tek representatives. Available 6:00 AM - 4:30 PM
Call us at
Available 6:00 AM – 5:00 PM (PST) Business Days
Download
Download Manuals, Datasheets, Software and more:
Feedback
P7600 Series TriMode™ Probes
More Information
- Que đo máy hiện sóng chênh lệch điện áp thấp
- Product Support
- Explore more Software models
Read Online:
The P7600 Series TriMode probes and the MSO/DPO70000DX and DPO/DSA70000D Series Oscilloscopes are designed to deliver the industry's lowest system noise levels. This high sensitivity is critical for being able to make accurate measurements on low amplitude signals.
Key performance specs
- Full 33 GHz bandwidth to the probe tip (P7633)
- Industry's lowest probe and oscilloscope system noise
Key features
- TriMode™ probe - one setup, three measurements without adjusting probe tip connections
- Differential
- Single ended
- Common mode
- Remote head design connectivity
- Allows placement of probe amplifier close to the circuit being measured
- Coaxial adapters
- 2.92mm
- SMP
- P7500 probe tip adapter
- Use P7500 Series TriMode solder-in probe tips
- Probe automatically detects tips and applies DSP correction filters
- Probe-specific S-parameters
- Unique DSP filters created from data stored in the probe
- TekConnect® Interface - TekConnect scope/probe control and usability
- Direct control from probe compensation box or from scope menu
Applications
- Including, but not
limited to:
- MIPI M-PHY, PCI Express, Serial ATA, Serial Attached SCSI, Fibre Channel, and HDMI
Combining TriMode probing with low noise performance
TriMode probing enhances productivity by enabling differential, single-ended, and common mode measurements with a single probe setup. Connecting a probe to the device under test can be a time consuming activity, especially if the probe has to be set up differently to make all the necessary measurements. TriMode probing improves productivity by reducing setup time, because only one setup is needed to make the three different types of measurements. Switching between Differential Mode [A-B], Single-Ended Mode [A-Gnd, B-Gnd], and Common Mode [((A+B)/2)-Gnd] is as easy as a press of a button.
As high speed serial data standards increase in speed and signal swings shrink, probes with high bandwidth coupled with low noise and high sensitivity are increasingly important for making accurate measurements.
The MSO/DPO70000DX and DPO70000SX Series oscilloscopes and the P7600 Series TriMode probes were designed to deliver the industry's lowest system noise levels. When used with a P76CA-xxx Coaxial Adapters, the vertical setting on the oscilloscope can be set as low as 3.48 mV/div with a system noise <1.1 mVrms at 33 GHz bandwidth.
This high sensitivity is critical for being able to make accurate measurements on low amplitude signals. The P7600 Series TriMode probes were designed to deliver superior sensitivity and allow the oscilloscope to directly measure small signals without using a zoom function. Using a zoom function to look at small signals does not change the intrinsic noise floor of the instrument which can make measurements on small signals problematic.
Connectivity
The P7600 Series probes utilize an interchangeable active tip design built around a custom tip interface using high frequency SMPM connectors. The P7600 Series probes feature an Automatic Adapter ID function that recognizes the attached adapter and automatically applies the correct DSP filters that eliminate imperfections in the frequency response all the way to the probe tip. This feature eliminates the risk of manually selecting the wrong tip type and is more efficient for the user.
Coaxial adapters
Coaxial adapters enable the probe to act like a differential input channel for the oscilloscope which effectively doubles the number of differential signals a single oscilloscope can measure simultaneously.
P76CA-292
33 GHz Bandwidth Coaxial Adapter with 2.92 mm (Female) connectors. This adapter is calibrated at the input connectors and is ideal for use with off the shelf or custom cables. Low skew cable pairs should be used to preserve full bandwidth performance.
P76CA-292C
33 GHz Bandwidth Coaxial Adapter with 2.92 mm (Male) connectors and 6" of high performance cable. This adapter is calibrated at the input connectors and is ideal for directly connecting to devices with 2.92 mm or SMA output connectors.
P76CA-SMP
33 GHz Bandwidth Coaxial Adapter with SMP (Female) connectors and 6" of high performance cable. This adapter is calibrated at the input connectors and is ideal for directly connecting to devices with SMP output connectors.
P7500 Series solder tip adapter
This adapter allows the P7630 probe to use existing Tektronix P7500 probe tips. The P7600 Series probe amplifiers have a 50 Ω input. When combined with a P7500 probe tip, the probe turns into a passive Z0 style probe with 450 Ω of differential input impedance. While Z0 probes can typically present a significant DC load to the device under test, the P7600 Series probes will minimize the effect of DC loading through the use of termination voltage adjustment.
P76TA
30 GHz Bandwidth P7500 Tip Adapter. The probe and oscilloscope system will support up to 30 GHz of bandwidth when this adapter is used with the P75PST Performance Solder Tip.
Unique probe filters
The P7600 Series probes contain probe specific S-parameter data. Attaching a P7600 probe to a MSO/DPO70000DX or DPO70000SX oscilloscope transfers this data to the instrument to create unique system DSP filters based on the specific S-parameter data of the oscilloscope and the probe. Creating unique filters based on the specific response of the system is critical as bandwidths increase. At bandwidths of 33 GHz, small variations in the signal path can lead to significant variation in frequency response. These variations are corrected using DSP filtering.
Specifications
Model Overview
Typical system specifications
Probe model | P7633 | P7625 | ||
---|---|---|---|---|
Adapter | P76CA-xxx | P76TA | P76CA-xxx | P76TA |
Characteristic | (Typical) | (Typical) | (Typical) | (Typical) |
Bandwidth (typical) | 33 GHz | 30 GHz | 25 GHz | 25 GHz |
Rise time (10-90%) (typical) | 14 ps | 16 ps | 18 ps | 18 ps |
Rise time (20-80%) (typical) | 11 ps | 12 ps | 14 ps | 14 ps |
Characteristics
The following characteristics are typical unless noted as guaranteed.
- Attenuation
- P76CA-xxx
- 0.25X / 0.5X / 1X / 2X / 4X
- P76TA
- 1.25X / 2.5X / 5X / 10X / 20X
- Input voltage range
- P76CA-xxx
- 1.2 Vpp single-ended, 2.0 Vpp differential
- P76TA
- 6.0 Vpp single-ended, 10.0 Vpp differential
- Operating voltage window
- P76CA-xxx
- -4 V to +4 V
- P76TA
- -5 V to +5 V
- Offset voltage range
- -4 V to +4 V
- Termination voltage range
- -4 V to +4 V
- DC input resistance
- P76CA-xxx
- 50 Ω ±2 Ω
- P76TA
- 225 Ω
- DC output zero common mode imbalance (guaranteed)
- < +/- 4 mV
- DC gain accuracy, probe only (guaranteed)
- +/- 2.0% all gain settings
- Input return loss
- P76CA-xxx
>20 dB to 5 GHz
>12 dB 5 GHz to 20 GHz
>10 dB 20 GHz to 30 GHz
>8 dB 30 GHz to 33 GHz
- P76TA
- NA
- Z min
- P76CA-xxx
- NA
- P76TA
- 225 Ω at 1 GHz, 150 Ω at 10 GHz, 100 Ω at 25 GHz
- Noise, referred to input (System noise with oscilloscope set in minimum V/div setting)
- <1.1 mVrms (33 GHz)
- <0.9 mVrms (25 GHz)
- CMRR (differential mode)
- P76CA-xxx
>40 dB at DC
>14 dB DC to 15 GHz
>6 dB 15 GHz to 30 GHz
>4 dB 30 GHz to 33 GHz
- P76TA
- NA
- Nondestructive input voltage range
- P76CA-xxx
- -5 V to +5 V (DC + peak AC)
- P76TA
- -8 V to +8 V (DC + peak AC)
- Interface
- TekConnect
- Minimum system requirements
Instrument Bandwidth Firmware version Recommended probe MSO/DPO73304DX, DPO73304SX, and DPO/DSA73304D 33 GHz V6.8 and above P7633 MSO/DPO72504DX, DPO73304SX, and DPO/DSA72504D 25 GHz V6.8 and above P7625
Environmental characteristics
- Temperature
- Operating
0 to +40 °C (+32 °F to +104 °F)
- Nonoperating
-20 °C to +71 °C (-4 °F to +160 °F)
- Humidity
- Operating
Up to +40 °C (+104 °F) 20%-80% RH
- Nonoperating
+30 °C to +46 °C (+86 °F to +115 °F) 0-90% RH
- Altitude
- Operating
3000 meters (9842 feet)
- Nonoperating
12000 meters (39,370 feet)
Ordering information
Models
- P7633
- Low Noise TriMode™ Probe, 33 GHz, TekConnect Interface
- P7625
- Low Noise TriMode™ Probe, 25 GHz, TekConnect Interface
NOTE: All P7600 Series probes require a P76CA-SMP, P76CA-292, P76CA-292C, or P76TA adapter for connection to the device under test. These adapters are ordered separately.
Options
Service options
- Opt. C3
- Calibration Service 3 Years
- Opt. C5
- Calibration Service 5 Years
- Opt. D3
- Calibration Data Report 3 Years (with Opt. C3)
- Opt. D5
- Calibration Data Report 5 Years (with Opt. C5)
- Opt. G3
- Complete Care 3 Years (includes loaner, scheduled calibration, and more)
- Opt. G5
- Complete Care 5 Years (includes loaner, scheduled calibration, and more)
- Opt. R3
- Repair Service 3 Years (including warranty)
- Opt. R3DW
Repair Service Coverage 3 Years (includes product warranty period). 3-year period starts at time of instrument purchase
- Opt. R5
- Repair Service 5 Years (including warranty)
- Opt. R5DW
Repair Service Coverage 5 Years (includes product warranty period). 5-year period starts at time of instrument purchase
Accessories
Standard accessories
Accessory | Quantity | Tektronix part number |
---|---|---|
Printed Manual | 1 kit | 071-3026-xx |
Data Calibration Report: Lists the manufacturing test results of your probe at the time of shipment | 1 each | Standard with probe |
Certificate of Traceable Calibration | 1 each | Standard with probe |
Antistatic wrist strap | 1 each | 006-3415-xx |
DC probe calibration fixture | 1 each | 067-3259-xx |
50 Ω BNC-M to BNC-M cable assembly, 10 in. | 1 each | 012-0208-xx |
ESD protective cap | 3 each | 276-1152-xx |
Hex wrench, 2 mm | 1 each | 129-2781-xx |
Color band kit | 1 kit | 016-0633-xx |
Recommended accessories
Description | Tektronix part number |
---|---|
2.92 mm Coaxial Adapter | P76CA-292 |
2.92 mm Coaxial Adapter with Cables | P76CA-292C |
SMP Coaxial Adapter with Cables | P76CA-SMP |
P7500 Tip Adapter | P76TA |
P7500 TriMode Performance Solder Tip | P75PST |
P7500 TriMode Long Reach Solder Tip | P75TLRST |
P7500 TriMode Resistor Solder Tip | 020-2936-xx |
P7500 TriMode Extended Resistor Solder Tip | 020-2944-xx |
Solder Tip Ramps, Kit of 25 | 020-3118-xx |
Adhesive Tip Tape, Strip of 10 | 006-8237-xx |
Deskew Fixture | 067-2431-xx |
SMPM Bullet Removal Tool | 003-1934-xx |
SMPM Replacement Bullet Contacts (package of 4) | 020-3105-xx |
G3PO Bullet Removal Tool | 003-1896-xx |
G3PO Replacement Bullet Contacts (package of 4) | 013-0359-xx |
Wire Kit | 017-0103-xx |
Replacement Resistor Kit | 020-2937-xx |